B2 ESPHome yaml for home assistant without tuya

[admin]

Code:

esphome:
  name: b2
  friendly_name: b2

esp32:
  board: esp32-s3-devkitc-1
  framework:
    type: arduino
   

# Enable logging
logger:
   hardware_uart: USB_SERIAL_JTAG
# Enable Home Assistant API
api:

ethernet:
  type: W5500
  clk_pin: GPIO1
  mosi_pin: GPIO2
  miso_pin: GPIO41
  cs_pin: GPIO42
  interrupt_pin: GPIO43
  reset_pin: GPIO44

i2c:
   - id: bus_a
     sda: 8
     scl: 18
     scan: true
     frequency: 400kHz

uart:
  - id: uart_1    #RS485
    baud_rate: 9600
    debug:
      direction: BOTH
      dummy_receiver: true
      after:
        timeout: 10ms
    tx_pin: 38
    rx_pin: 39


switch:
  - platform: uart
    uart_id: uart_1
    name: "RS485 Button"
    data: [0x11, 0x22, 0x33, 0x44, 0x55]

  - platform: gpio
    name: "b2-output01"
    pin: 4
    inverted: false

  - platform: gpio
    name: "b2-output02"
    pin: 46
    inverted: false

binary_sensor:
  - platform: gpio
    name: "b2-input01"
    pin:
      number: 6
      inverted: true

  - platform: gpio
    name: "b2-input02"
    pin:
      number: 7
      inverted: true


##pull-up resistance on PCB
  - platform: gpio
    name: "b2-W1-io47"
    pin:
      number: 47
      inverted: true

  - platform: gpio
    name: "b2-W1-io48"
    pin:
      number: 48
      inverted: true

  - platform: gpio
    name: "b2-W1-io17"
    pin:
      number: 17
      inverted: true

  - platform: gpio
    name: "b2-W1-io40"
    pin:
      number: 40
      inverted: true


ads1115:
  - address: 0x48
sensor:
  - platform: ads1115
    multiplexer: 'A0_GND'
    gain: 6.144
    resolution: 16_BITS
    name: "ADS1115 Channel A0-GND"
    update_interval: 5s
  - platform: ads1115
    multiplexer: 'A1_GND'
    gain: 6.144
    name: "ADS1115 Channel A1-GND"
    update_interval: 5s
  - platform: ads1115
    multiplexer: 'A2_GND'
    gain: 6.144
    name: "ADS1115 Channel A2-GND"
    update_interval: 5s
  - platform: ads1115
    multiplexer: 'A3_GND'
    gain: 6.144
    name: "ADS1115 Channel A3-GND"
    update_interval: 5s

web_server:
  port: 80

font:
  - file: "gfonts://Roboto"
    id: roboto
    size: 20

display:
  - platform: ssd1306_i2c
    i2c_id: bus_a
    model: "SSD1306 128x64"
    address: 0x3C
    lambda: |-
      it.printf(0, 0, id(roboto), "KinCony B2");

download yaml file:

  B2-HA-Without-Tuya.txt (Size: 2.35 KB / Downloads: 7)