KC868-HA RS485 INPUT & OUTPUT plugin for ESPHome

[gizmo]

can you post the newest yaml with latest KC868-HA component (v3.0.0).

esphome:
  name: dingtian-4ch
  friendly_name: dingtian-4ch

esp32:
  board: esp32dev
  framework:
    type: arduino

# Enable logging
logger:
  baud_rate: 0

# Enable Home Assistant API
api:
  encryption:
    key: "XXX"

ota:
  password: "XXX"

status_led:
  pin:
    number: GPIO15
    inverted: true

uart:
  id: myuart1
  tx_pin: GPIO1
  rx_pin: GPIO3
  baud_rate: 9600

ethernet:
  type: JL1101
  mdc_pin: GPIO23
  mdio_pin: GPIO18
  phy_addr: 0
  clk_mode: GPIO17_OUT
  # The PHY chip has a pin labeled TX_EN that goes to GPIO 21 on ESP
  # and the RSTn pin on the phy goes to GPIO0
  ##
  # Datasheet indicates the RSTn should be LOW to disable the phy and default is high
  power_pin: GPIO0

external_components:
  - source:
      type: git
      url: https://github.com/hzkincony/esphome-kc868-ha
      ref: main

kc868_ha:

binary_sensor:
  - platform: kc868_ha
    target_relay_controller_addr: 1 # Default value is 1, corresponds to the Target Relay Controller Addr parameter in HA485_Ctrl software
    switch_adapter_addr: 10 # Default value is 10, corresponds to the Switch Adapter Addr parameter in HA485_Ctrl software
    bind_output: 1 # Corresponds to the BindOutput parameter in HA485_Ctrl software
    name: "binary_sensor 1"
  - platform: kc868_ha
    target_relay_controller_addr: 1
    switch_adapter_addr: 10
    bind_output: 2
    name: "binary_sensor 2"
  - platform: kc868_ha
    target_relay_controller_addr: 1
    switch_adapter_addr: 10
    bind_output: 3
    name: "binary_sensor 3"
  - platform: kc868_ha
    target_relay_controller_addr: 1
    switch_adapter_addr: 10
    bind_output: 4
    name: "binary_sensor 4"
  - platform: kc868_ha
    target_relay_controller_addr: 1
    switch_adapter_addr: 10
    bind_output: 5
    name: "binary_sensor 5"
  - platform: kc868_ha
    target_relay_controller_addr: 1
    switch_adapter_addr: 10
    bind_output: 6
    name: "binary_sensor 6"

switch:
  - platform: kc868_ha
    target_relay_controller_addr: 1
    switch_adapter_addr: 10
    bind_output: 1
    name: "switch 1"
  - platform: kc868_ha
    target_relay_controller_addr: 1
    switch_adapter_addr: 10
    bind_output: 2
    name: "switch 2"
  - platform: kc868_ha
    target_relay_controller_addr: 1
    switch_adapter_addr: 10
    bind_output: 3
    name: "switch 3"
  - platform: kc868_ha
    target_relay_controller_addr: 1
    switch_adapter_addr: 10
    bind_output: 4
    name: "switch 4"
  - platform: kc868_ha
    target_relay_controller_addr: 1
    switch_adapter_addr: 10
    bind_output: 5
    name: "switch 5"
  - platform: kc868_ha
    target_relay_controller_addr: 1
    switch_adapter_addr: 10
    bind_output: 6
    name: "switch 6"