esphome:
  name: kc868-a6

esp32:
  board: esp32dev
  framework:
    type: arduino

# Enable logging
logger:

# Enable Home Assistant API
api:

wifi:
  ssid: "KinCony"
  password: "a12345678"

  # Enable fallback hotspot (captive portal) in case wifi connection fails
  ap:
    ssid: "A6 Fallback Hotspot"
    password: "GLdHSsZr1p96"

captive_portal:


# Example configuration entry for ESP32


# Example configuration entry
pcf8574:
  - id: 'pcf8574_hub_out_1'  # for output channel 1-8
    address: 0x24

  - id: 'pcf8574_hub_in_1'  # for input channel 1-8
    address: 0x22

# Individual outputs
switch:
  - platform: gpio
    name: "a6-light1"
    id: light1
    pin:
      pcf8574: pcf8574_hub_out_1
      number: 0
      mode: OUTPUT
      inverted: true

  - platform: gpio
    name: "a6-light2"
    id: light2
    pin:
      pcf8574: pcf8574_hub_out_1
      number: 1
      mode: OUTPUT
      inverted: true
      
  - platform: gpio
    name: "a6-light3"
    id: light3
    pin:
      pcf8574: pcf8574_hub_out_1
      number: 2
      mode: OUTPUT
      inverted: true
      
  - platform: gpio
    name: "a6-light4"
    id: light4
    pin:
      pcf8574: pcf8574_hub_out_1
      number: 3
      mode: OUTPUT
      inverted: true
      
  - platform: gpio
    name: "a6-light5"
    id: light5
    pin:
      pcf8574: pcf8574_hub_out_1
      number: 4
      mode: OUTPUT
      inverted: true
      
  - platform: gpio
    name: "a6-light6"
    id: light6
    pin:
      pcf8574: pcf8574_hub_out_1
      number: 5
      mode: OUTPUT
      inverted: true
      

binary_sensor:
  - platform: gpio
    name: "a6-input1"
    pin:
      pcf8574: pcf8574_hub_in_1
      number: 0
      mode: INPUT
      inverted: true

  - platform: gpio
    name: "a6-input2"
    pin:
      pcf8574: pcf8574_hub_in_1
      number: 1
      mode: INPUT
      inverted: true

  - platform: gpio
    name: "a6-input3"
    pin:
      pcf8574: pcf8574_hub_in_1
      number: 2
      mode: INPUT
      inverted: true

  - platform: gpio
    name: "a6-input4"
    pin:
      pcf8574: pcf8574_hub_in_1
      number: 3
      mode: INPUT
      inverted: true

  - platform: gpio
    name: "a6-input5"
    pin:
      pcf8574: pcf8574_hub_in_1
      number: 4
      mode: INPUT
      inverted: true

  - platform: gpio
    name: "a6-input6"
    pin:
      pcf8574: pcf8574_hub_in_1
      number: 5
      mode: INPUT
      inverted: true

one_wire:
  - platform: gpio
    pin: GPIO32

sensor:
  - platform: adc
    pin: 36
    name: "A1 Voltage"
    update_interval: 5s
    attenuation: 11db
    filters:
      - multiply: 0.001221

  - platform: adc
    pin: 39
    name: "A2 Voltage"
    update_interval: 5s
    attenuation: 11db
    filters:
      - multiply: 0.001221
  - platform: adc
    pin: 34
    name: "A3 Voltage"
    update_interval: 5s
    attenuation: 11db
    filters:
      - multiply: 0.001221
  - platform: adc
    pin: 35
    name: "A4 Voltage"
    update_interval: 5s
    attenuation: 11db
    filters:
      - multiply: 0.001221

  - platform: dallas_temp
    address: 0x290621405cc19d28
    name: temperature

output:
  - platform: esp32_dac
    pin: GPIO26
    id: dac_output1
  - platform: esp32_dac
    pin: GPIO25
    id: dac_output2

light:
  - platform: monochromatic
    output: dac_output1
    gamma_correct: 2
    name: "Dimmer01"
  - platform: monochromatic
    output: dac_output2
    gamma_correct: 2
    name: "Dimmer02"

uart:
  tx_pin: GPIO17
  rx_pin: GPIO16
  baud_rate: 9600

# set the RS232 UART command as a button
# when pressed button, will send string "This is KinCony"

button:
  - platform: uart
    name: "RS232 message button"
    data: 'hello this is KinCony from RS232'

i2c:
  sda: 4
  scl: 15
  scan: true
  id: bus_a

font:
  - file: "gfonts://Roboto"
    id: kincony_font
    size: 20
    bpp: 2

display:
  - platform: ssd1306_i2c
    model: "SSD1306 128x64"
    address: 0x3C
    lambda: |-
      it.print(0, 0, id(kincony_font), "Hello World!");

mqtt:
  broker: 192.168.3.133
  username: mqtt
  password: 123