INFO ESPHome 2026.2.4
INFO Reading configuration /config/esphome/kincony-e16s-red.yaml...
WARNING GPIO15 is a strapping PIN and should only be used for I/O with care.
Attaching external pullup/down resistors to strapping pins can cause unexpected failures.
See https://esphome.io/guides/faq/#why-am-i-getting-a-warning-about-strapping-pins
WARNING GPIO2 is a strapping PIN and should only be used for I/O with care.
Attaching external pullup/down resistors to strapping pins can cause unexpected failures.
See https://esphome.io/guides/faq/#why-am-i-getting-a-warning-about-strapping-pins
INFO Starting log output from kincony-e16s-red.local using esphome API
INFO Successfully resolved kincony-e16s-red.local in 0.287s
INFO Successfully connected to kincony-e16s-red @ 192.168.20.53 in 0.109s
INFO Successful handshake with kincony-e16s-red @ 192.168.20.53 in 0.136s
[14:48:55.930][I][app:215]: ESPHome version 2026.2.4 compiled on 2026-09-05 14:21:34 -0300
[14:48:55.942][I][app:222]: ESP32 Chip: ESP32 rev3.1, 2 core(s)
[14:48:55.943][W][app:231]: Set minimum_chip_revision: "3.1" to reduce binary size
[14:48:55.945][C][logger:237]: Logger:
[14:48:55.945][C][logger:237]:   Max Level: DEBUG
[14:48:55.945][C][logger:237]:   Initial Level: DEBUG
[14:48:55.945][C][logger:244]:   Log Baud Rate: 0
[14:48:55.945][C][logger:244]:   Hardware UART: UART0
[14:48:55.946][C][logger:254]:   Task Log Buffer Size: 768 bytes
[14:48:55.973][C][i2c.idf:093]: I2C Bus:
[14:48:55.974][C][i2c.idf:094]:   SDA Pin: GPIO16
[14:48:55.974][C][i2c.idf:094]:   SCL Pin: GPIO15
[14:48:55.974][C][i2c.idf:094]:   Frequency: 50000 Hz
[14:48:55.974][C][i2c.idf:104]:   Recovery: bus successfully recovered
[14:48:55.978][C][i2c.idf:114]: Results from bus scan:
[14:48:55.979][C][i2c.idf:120]: Found device at address 0x21
[14:48:55.979][C][i2c.idf:120]: Found device at address 0x22
[14:48:55.983][C][i2c.idf:120]: Found device at address 0x24
[14:48:55.983][C][i2c.idf:120]: Found device at address 0x25
[14:48:55.983][C][uart.idf:230]: UART Bus 0:
[14:48:55.984][C][uart.idf:152]:   TX Pin: GPIO32
[14:48:55.985][C][uart.idf:152]:   RX Pin: GPIO13
[14:48:55.985][C][uart.idf:235]:   RX Buffer Size: 256
[14:48:55.985][C][uart.idf:235]:   RX Full Threshold: 8
[14:48:55.985][C][uart.idf:235]:   RX Timeout: 2
[14:48:55.993][C][uart.idf:241]:   Baud Rate: 9600 baud
[14:48:55.993][C][uart.idf:241]:   Data Bits: 8
[14:48:55.993][C][uart.idf:241]:   Parity: NONE
[14:48:55.993][C][uart.idf:241]:   Stop bits: 1
[14:48:55.994][C][pcf8574:024]: PCF8574:
[14:48:55.994][C][pcf8574:024]:   Is PCF8575: NO
[14:48:55.994][C][pcf8574:028]:   Address: 0x21
[14:48:56.005][C][pcf8574:024]: PCF8574:
[14:48:56.005][C][pcf8574:024]:   Is PCF8575: NO
[14:48:56.015][C][pcf8574:028]:   Address: 0x25
[14:48:56.015][C][pcf8574:024]: PCF8574:
[14:48:56.015][C][pcf8574:024]:   Is PCF8575: NO
[14:48:56.029][C][pcf8574:028]:   Address: 0x22
[14:48:56.032][C][pcf8574:024]: PCF8574:
[14:48:56.032][C][pcf8574:024]:   Is PCF8575: NO
[14:48:56.033][C][pcf8574:028]:   Address: 0x24
[14:48:56.060][C][switch.gpio:092]: GPIO Switch 'Onboard Buzzer'
[14:48:56.060][C][switch.gpio:092]:   Restore Mode: always OFF
[14:48:56.064][C][switch.gpio:152]:   Pin: GPIO2
[14:48:56.064][C][switch.gpio:092]: GPIO Switch 'e16s-output1'
[14:48:56.064][C][switch.gpio:092]:   Restore Mode: restore defaults to OFF
[14:48:56.088][C][switch.gpio:152]:   Pin: 0 via PCF8574
[14:48:56.088][C][switch.gpio:092]: GPIO Switch 'e16s-output2'
[14:48:56.088][C][switch.gpio:092]:   Restore Mode: restore defaults to OFF
[14:48:56.089][C][switch.gpio:152]:   Pin: 1 via PCF8574
[14:48:56.097][C][switch.gpio:092]: GPIO Switch 'e16s-output3'
[14:48:56.097][C][switch.gpio:092]:   Restore Mode: restore defaults to OFF
[14:48:56.098][C][switch.gpio:152]:   Pin: 2 via PCF8574
[14:48:56.098][C][switch.gpio:092]: GPIO Switch 'e16s-output4'
[14:48:56.098][C][switch.gpio:092]:   Restore Mode: restore defaults to OFF
[14:48:56.122][C][switch.gpio:152]:   Pin: 3 via PCF8574
[14:48:56.123][C][switch.gpio:092]: GPIO Switch 'e16s-output5'
[14:48:56.123][C][switch.gpio:092]:   Restore Mode: restore defaults to OFF
[14:48:56.123][C][switch.gpio:152]:   Pin: 4 via PCF8574
[14:48:56.134][C][switch.gpio:092]: GPIO Switch 'e16s-output6'
[14:48:56.134][C][switch.gpio:092]:   Restore Mode: restore defaults to OFF
[14:48:56.135][C][switch.gpio:152]:   Pin: 5 via PCF8574
[14:48:56.135][C][switch.gpio:092]: GPIO Switch 'e16s-output7'
[14:48:56.135][C][switch.gpio:092]:   Restore Mode: restore defaults to OFF
[14:48:56.151][C][switch.gpio:152]:   Pin: 6 via PCF8574
[14:48:56.154][C][switch.gpio:092]: GPIO Switch 'e16s-output8'
[14:48:56.154][C][switch.gpio:092]:   Restore Mode: restore defaults to OFF
[14:48:56.155][C][switch.gpio:152]:   Pin: 7 via PCF8574
[14:48:56.163][C][switch.gpio:092]: GPIO Switch 'e16s-output9'
[14:48:56.163][C][switch.gpio:092]:   Restore Mode: restore defaults to OFF
[14:48:56.164][C][switch.gpio:152]:   Pin: 0 via PCF8574
[14:48:56.173][C][switch.gpio:092]: GPIO Switch 'e16s-output10'
[14:48:56.173][C][switch.gpio:092]:   Restore Mode: restore defaults to OFF
[14:48:56.174][C][switch.gpio:152]:   Pin: 1 via PCF8574
[14:48:56.175][C][switch.gpio:092]: GPIO Switch 'e16s-output11'
[14:48:56.175][C][switch.gpio:092]:   Restore Mode: restore defaults to OFF
[14:48:56.175][C][switch.gpio:152]:   Pin: 2 via PCF8574
[14:48:56.201][C][switch.gpio:092]: GPIO Switch 'e16s-output12'
[14:48:56.201][C][switch.gpio:092]:   Restore Mode: restore defaults to OFF
[14:48:56.201][C][switch.gpio:152]:   Pin: 3 via PCF8574
[14:48:56.202][C][switch.gpio:092]: GPIO Switch 'e16s-output13'
[14:48:56.202][C][switch.gpio:092]:   Restore Mode: restore defaults to OFF
[14:48:56.206][C][switch.gpio:152]:   Pin: 4 via PCF8574
[14:48:56.221][C][switch.gpio:092]: GPIO Switch 'e16s-output14'
[14:48:56.221][C][switch.gpio:092]:   Restore Mode: restore defaults to OFF
[14:48:56.222][C][switch.gpio:152]:   Pin: 5 via PCF8574
[14:48:56.230][C][switch.gpio:092]: GPIO Switch 'e16s-output15'
[14:48:56.230][C][switch.gpio:092]:   Restore Mode: restore defaults to OFF
[14:48:56.231][C][switch.gpio:152]:   Pin: 6 via PCF8574
[14:48:56.246][C][switch.gpio:092]: GPIO Switch 'e16s-output16'
[14:48:56.246][C][switch.gpio:092]:   Restore Mode: restore defaults to OFF
[14:48:56.249][C][switch.gpio:152]:   Pin: 7 via PCF8574
[14:48:56.250][C][gpio.binary_sensor:016]: GPIO Binary Sensor 'e16s-input16'
[14:48:56.250][C][gpio.binary_sensor:152]:   Pin: 0 via PCF8574
[14:48:56.268][C][gpio.binary_sensor:069]:   Mode: polling
[14:48:56.268][C][gpio.binary_sensor:016]: GPIO Binary Sensor 'e16s-input15'
[14:48:56.268][C][gpio.binary_sensor:152]:   Pin: 1 via PCF8574
[14:48:56.277][C][gpio.binary_sensor:069]:   Mode: polling
[14:48:56.277][C][gpio.binary_sensor:016]: GPIO Binary Sensor 'e16s-input14'
[14:48:56.277][C][gpio.binary_sensor:152]:   Pin: 2 via PCF8574
[14:48:56.298][C][gpio.binary_sensor:069]:   Mode: polling
[14:48:56.298][C][gpio.binary_sensor:016]: GPIO Binary Sensor 'e16s-input13'
[14:48:56.299][C][gpio.binary_sensor:152]:   Pin: 3 via PCF8574
[14:48:56.302][C][gpio.binary_sensor:069]:   Mode: polling
[14:48:56.302][C][gpio.binary_sensor:016]: GPIO Binary Sensor 'e16s-input12'
[14:48:56.302][C][gpio.binary_sensor:152]:   Pin: 4 via PCF8574
[14:48:56.317][C][gpio.binary_sensor:069]:   Mode: polling
[14:48:56.317][C][gpio.binary_sensor:016]: GPIO Binary Sensor 'e16s-input11'
[14:48:56.317][C][gpio.binary_sensor:152]:   Pin: 5 via PCF8574
[14:48:56.318][C][gpio.binary_sensor:069]:   Mode: polling
[14:48:56.318][C][gpio.binary_sensor:016]: GPIO Binary Sensor 'e16s-input10'
[14:48:56.319][C][gpio.binary_sensor:152]:   Pin: 6 via PCF8574
[14:48:56.343][C][gpio.binary_sensor:069]:   Mode: polling
[14:48:56.343][C][gpio.binary_sensor:016]: GPIO Binary Sensor 'e16s-input9'
[14:48:56.344][C][gpio.binary_sensor:152]:   Pin: 7 via PCF8574
[14:48:56.347][C][gpio.binary_sensor:069]:   Mode: polling
[14:48:56.347][C][gpio.binary_sensor:016]: GPIO Binary Sensor 'e16s-input8'
[14:48:56.347][C][gpio.binary_sensor:152]:   Pin: 0 via PCF8574
[14:48:56.359][C][gpio.binary_sensor:069]:   Mode: polling
[14:48:56.359][C][gpio.binary_sensor:016]: GPIO Binary Sensor 'e16s-input7'
[14:48:56.359][C][gpio.binary_sensor:152]:   Pin: 1 via PCF8574
[14:48:56.363][C][gpio.binary_sensor:069]:   Mode: polling
[14:48:56.364][C][gpio.binary_sensor:016]: GPIO Binary Sensor 'e16s-input6'
[14:48:56.364][C][gpio.binary_sensor:152]:   Pin: 2 via PCF8574
[14:48:56.384][C][gpio.binary_sensor:069]:   Mode: polling
[14:48:56.385][C][gpio.binary_sensor:016]: GPIO Binary Sensor 'e16s-input5'
[14:48:56.385][C][gpio.binary_sensor:152]:   Pin: 3 via PCF8574
[14:48:56.394][C][gpio.binary_sensor:069]:   Mode: polling
[14:48:56.394][C][gpio.binary_sensor:016]: GPIO Binary Sensor 'e16s-input4'
[14:48:56.395][C][gpio.binary_sensor:152]:   Pin: 4 via PCF8574
[14:48:56.407][C][gpio.binary_sensor:069]:   Mode: polling
[14:48:56.408][C][gpio.binary_sensor:016]: GPIO Binary Sensor 'e16s-input3'
[14:48:56.408][C][gpio.binary_sensor:152]:   Pin: 5 via PCF8574
[14:48:56.432][C][gpio.binary_sensor:069]:   Mode: polling
[14:48:56.435][C][gpio.binary_sensor:016]: GPIO Binary Sensor 'e16s-input2'
[14:48:56.436][C][gpio.binary_sensor:152]:   Pin: 6 via PCF8574
[14:48:56.440][C][gpio.binary_sensor:069]:   Mode: polling
[14:48:56.440][C][gpio.binary_sensor:016]: GPIO Binary Sensor 'e16s-input1'
[14:48:56.441][C][gpio.binary_sensor:152]:   Pin: 7 via PCF8574
[14:48:56.492][C][gpio.binary_sensor:069]:   Mode: polling
[14:48:56.575][C][kc868_ha:075]: KC868HaComponent::dump_config
[14:48:56.583][C][kc868_ha:098]: KC868HaSwitch::dump_config
[14:48:56.592][C][kc868_ha:098]: KC868HaSwitch::dump_config
[14:48:56.602][C][kc868_ha:098]: KC868HaSwitch::dump_config
[14:48:56.619][C][kc868_ha:098]: KC868HaSwitch::dump_config
[14:48:56.641][C][kc868_ha:098]: KC868HaSwitch::dump_config
[14:48:56.643][C][kc868_ha:098]: KC868HaSwitch::dump_config
[14:48:56.643][C][kc868_ha:083]: KC868HaBinarySensor::dump_config
[14:48:56.667][C][kc868_ha:083]: KC868HaBinarySensor::dump_config
[14:48:56.686][C][kc868_ha:083]: KC868HaBinarySensor::dump_config
[14:48:56.694][C][kc868_ha:083]: KC868HaBinarySensor::dump_config
[14:48:56.714][C][kc868_ha:083]: KC868HaBinarySensor::dump_config
[14:48:56.717][C][kc868_ha:083]: KC868HaBinarySensor::dump_config
[14:48:56.717][C][wifi:1450]: WiFi:
[14:48:56.717][C][wifi:1450]:   Local MAC: 14:33:5C:23:B8:04
[14:48:56.717][C][wifi:1450]:   Connected: YES
[14:48:56.740][C][wifi:1202]:   IP Address: 192.168.20.53
[14:48:56.741][C][wifi:1213]:   SSID: '302 Moved Temporarily'[redacted]
[14:48:56.741][C][wifi:1213]:   BSSID: 7C:2E:BD:76:99:BB[redacted]
[14:48:56.741][C][wifi:1213]:   Hostname: 'kincony-e16s-red'
[14:48:56.741][C][wifi:1213]:   Signal strength: -37 dB ▂▄▆█
[14:48:56.741][C][wifi:1213]:   Channel: 6
[14:48:56.741][C][wifi:1213]:   Subnet: 255.255.255.0
[14:48:56.741][C][wifi:1213]:   Gateway: 192.168.20.1
[14:48:56.741][C][wifi:1213]:   DNS1: 192.168.20.1
[14:48:56.741][C][wifi:1213]:   DNS2: 0.0.0.0
[14:48:56.746][C][esphome.ota:075]: Over-The-Air updates:
[14:48:56.746][C][esphome.ota:075]:   Address: kincony-e16s-red.local:3232
[14:48:56.746][C][esphome.ota:075]:   Version: 2
[14:48:56.748][C][esphome.ota:082]:   Password configured
[14:48:56.749][C][safe_mode:022]: Safe Mode:
[14:48:56.749][C][safe_mode:022]:   Successful after: 60s
[14:48:56.749][C][safe_mode:022]:   Invoke after: 10 attempts
[14:48:56.749][C][safe_mode:022]:   Duration: 300s
[14:48:56.749][C][safe_mode:039]:   Bootloader rollback: supported
[14:48:56.780][C][api:237]: Server:
[14:48:56.780][C][api:237]:   Address: kincony-e16s-red.local:6053
[14:48:56.780][C][api:237]:   Listen backlog: 4
[14:48:56.780][C][api:237]:   Max connections: 8
[14:48:56.781][C][api:244]:   Noise encryption: YES
[14:48:56.781][C][mdns:177]: mDNS:
[14:48:56.781][C][mdns:177]:   Hostname: kincony-e16s-red
[14:48:56.895][D][switch:026]: 'Onboard Buzzer' Turning OFF.