INFO ESPHome 2023.12.3
INFO Reading configuration /config/esphome/dingtian-4ch.yaml...
WARNING GPIO15 is a strapping PIN and should only be used for I/O with care.
Attaching external pullup/down resistors to strapping pins can cause unexpected failures.
See https://esphome.io/guides/faq.html#why-am-i-getting-a-warning-about-strapping-pins
WARNING GPIO0 is a strapping PIN and should only be used for I/O with care.
Attaching external pullup/down resistors to strapping pins can cause unexpected failures.
See https://esphome.io/guides/faq.html#why-am-i-getting-a-warning-about-strapping-pins
WARNING GPIO12 is a strapping PIN and should only be used for I/O with care.
Attaching external pullup/down resistors to strapping pins can cause unexpected failures.
See https://esphome.io/guides/faq.html#why-am-i-getting-a-warning-about-strapping-pins
WARNING GPIO2 is a strapping PIN and should only be used for I/O with care.
Attaching external pullup/down resistors to strapping pins can cause unexpected failures.
See https://esphome.io/guides/faq.html#why-am-i-getting-a-warning-about-strapping-pins
INFO Starting log output from 10.0.10.148 using esphome API
INFO Successfully connected to dingtian-4ch @ 10.0.10.148 in 0.002s
INFO Successful handshake with dingtian-4ch @ 10.0.10.148 in 0.093s
[12:57:40][I][app:102]: ESPHome version 2023.12.3 compiled on Dec 24 2023, 16:45:34
[12:57:40][C][status_led:019]: Status LED:
[12:57:40][C][status_led:020]:   Pin: GPIO15
[12:57:40][C][logger:443]: Logger:
[12:57:40][C][logger:444]:   Level: DEBUG
[12:57:40][C][logger:445]:   Log Baud Rate: 0
[12:57:40][C][logger:447]:   Hardware UART: UART0
[12:57:40][C][uart.arduino_esp32:137]: UART Bus 0:
[12:57:40][C][uart.arduino_esp32:138]:   TX Pin: GPIO1
[12:57:40][C][uart.arduino_esp32:139]:   RX Pin: GPIO3
[12:57:40][C][uart.arduino_esp32:141]:   RX Buffer Size: 256
[12:57:40][C][uart.arduino_esp32:143]:   Baud Rate: 9600 baud
[12:57:40][C][uart.arduino_esp32:144]:   Data Bits: 8
[12:57:40][C][uart.arduino_esp32:145]:   Parity: NONE
[12:57:40][C][uart.arduino_esp32:146]:   Stop bits: 1
[12:57:40][C][template.text_sensor:020]: Template Sensor 'S2 Button'
[12:57:40][C][gpio.binary_sensor:015]: GPIO Binary Sensor 'User Input 1'
[12:57:40][C][gpio.binary_sensor:016]:   Pin: GPIO36
[12:57:40][C][gpio.binary_sensor:015]: GPIO Binary Sensor 'User Input 2'
[12:57:40][C][gpio.binary_sensor:016]:   Pin: GPIO39
[12:57:40][C][gpio.binary_sensor:015]: GPIO Binary Sensor 'User Input 3'
[12:57:40][C][gpio.binary_sensor:016]:   Pin: GPIO33
[12:57:40][C][gpio.binary_sensor:015]: GPIO Binary Sensor 'User Input 4'
[12:57:40][C][gpio.binary_sensor:016]:   Pin: GPIO35
[12:57:40][C][switch.gpio:068]: GPIO Switch 'Relay 1'
[12:57:40][C][switch.gpio:091]:   Restore Mode: always OFF
[12:57:40][C][switch.gpio:031]:   Pin: GPIO12
[12:57:40][C][switch.gpio:068]: GPIO Switch 'Relay 2'
[12:57:40][C][switch.gpio:091]:   Restore Mode: always OFF
[12:57:40][C][switch.gpio:031]:   Pin: GPIO32
[12:57:40][C][switch.gpio:068]: GPIO Switch 'Relay 3'
[12:57:40][C][switch.gpio:091]:   Restore Mode: always OFF
[12:57:40][C][switch.gpio:031]:   Pin: GPIO2
[12:57:40][C][switch.gpio:068]: GPIO Switch 'Relay 4'
[12:57:40][C][switch.gpio:091]:   Restore Mode: always OFF
[12:57:40][C][switch.gpio:031]:   Pin: GPIO16
[12:57:41][C][gpio.binary_sensor:015]: GPIO Binary Sensor 'User Button'
[12:57:41][C][gpio.binary_sensor:016]:   Pin: GPIO34
[12:57:41][C][template.switch:068]: Template Switch 'LED Blink'
[12:57:41][C][template.switch:091]:   Restore Mode: always OFF
[12:57:41][C][template.switch:057]:   Optimistic: NO
[12:57:41][C][template.switch:068]: Template Switch 'LED Fast Blink'
[12:57:41][C][template.switch:091]:   Restore Mode: always OFF
[12:57:41][C][template.switch:057]:   Optimistic: NO
[12:57:41][C][template.switch:068]: Template Switch 'LED Very Fast Blink'
[12:57:41][C][template.switch:091]:   Restore Mode: always OFF
[12:57:41][C][template.switch:057]:   Optimistic: NO
[12:57:41][C][template.switch:068]: Template Switch 'Horn Honk'
[12:57:41][C][template.switch:091]:   Restore Mode: always OFF
[12:57:41][C][template.switch:057]:   Optimistic: NO
[12:57:41][C][kc868_ha.component:073]: KC868HaComponent::dump_config
[12:57:41][C][ethernet:222]: Ethernet:
[12:57:41][C][ethernet:354]:   IP Address: 10.0.10.148
[12:57:41][C][ethernet:355]:   Hostname: 'dingtian-4ch'
[12:57:41][C][ethernet:356]:   Subnet: 255.255.255.0
[12:57:41][C][ethernet:357]:   Gateway: 10.0.10.1
[12:57:41][C][ethernet:362]:   DNS1: 10.0.10.1
[12:57:41][C][ethernet:363]:   DNS2: 0.0.0.0
[12:57:41][C][ethernet:383]:   MAC Address: E0:5A:1B:D7:55:2F
[12:57:41][C][ethernet:388]:   Is Full Duplex: YES
[12:57:41][C][ethernet:393]:   Link Speed: 100
[12:57:41][C][ethernet:225]:   Power Pin: 0
[12:57:41][C][ethernet:227]:   MDC Pin: 23
[12:57:41][C][ethernet:228]:   MDIO Pin: 18
[12:57:41][C][ethernet:229]:   Type: JL1101
[12:57:41][C][ethernet:230]:   PHY addr: 0
[12:57:41][C][mdns:115]: mDNS:
[12:57:41][C][mdns:116]:   Hostname: dingtian-4ch
[12:57:41][C][ota:097]: Over-The-Air Updates:
[12:57:41][C][ota:098]:   Address: dingtian-4ch.local:3232
[12:57:41][C][ota:101]:   Using Password.
[12:57:41][C][api:139]: API Server:
[12:57:41][C][api:140]:   Address: dingtian-4ch.local:6053
[12:57:41][C][api:142]:   Using noise encryption: YES
[12:59:42][D][switch:012]: 'switch 1' Turning ON.
[12:59:42][D][kc868_ha.component:131]: uart bus send 1:3:12:55:bb:0:0:0:0:0:0:0:0:0:0:0:0:0:0:0:1:30:4b
[12:59:42][D][switch:055]: 'switch 1': Sending state ON
[12:59:44][D][switch:016]: 'switch 1' Turning OFF.
[12:59:44][D][kc868_ha.component:131]: uart bus send 1:3:12:55:bb:0:0:0:0:0:0:0:0:0:0:0:0:0:0:0:0:f1:8b
[12:59:44][D][switch:055]: 'switch 1': Sending state OFF
[12:59:48][D][switch:012]: 'switch 2' Turning ON.
[12:59:48][D][kc868_ha.component:131]: uart bus send 1:3:12:55:bb:0:0:0:0:0:0:0:0:0:0:0:0:0:0:0:2:70:4a
[12:59:48][D][switch:055]: 'switch 2': Sending state ON
[12:59:50][D][switch:016]: 'switch 2' Turning OFF.
[12:59:50][D][kc868_ha.component:131]: uart bus send 1:3:12:55:bb:0:0:0:0:0:0:0:0:0:0:0:0:0:0:0:0:f1:8b
[12:59:50][D][switch:055]: 'switch 2': Sending state OFF
[12:59:56][D][kc868_ha.component:019]: uart bus receive 1:10:0:a:0:6:c:0:0:0:0:0:0:0:0:0:0:6a:1:63:10
[12:59:56][D][kc868_ha.component:030]: uart crc=63:10, calc crc=63:10
[12:59:56][D][kc868_ha.component:046]: dump kc868_ha config, target_relay_controller_addr=1, switch_adapter_addr=10, bind_output=2
[12:59:56][D][kc868_ha.component:046]: dump kc868_ha config, target_relay_controller_addr=1, switch_adapter_addr=10, bind_output=3
[12:59:56][D][kc868_ha.component:046]: dump kc868_ha config, target_relay_controller_addr=1, switch_adapter_addr=10, bind_output=4
[12:59:56][D][kc868_ha.component:046]: dump kc868_ha config, target_relay_controller_addr=1, switch_adapter_addr=10, bind_output=5
[12:59:56][D][kc868_ha.component:046]: dump kc868_ha config, target_relay_controller_addr=1, switch_adapter_addr=10, bind_output=6
[12:59:56][D][kc868_ha.component:046]: dump kc868_ha config, target_relay_controller_addr=1, switch_adapter_addr=10, bind_output=1
[12:59:56][D][kc868_ha.component:057]: found a kc868_ha board, target_relay_controller_addr=1, switch_adapter_addr=10, bind_output=2
[12:59:56][D][kc868_ha.component:057]: found a kc868_ha board, target_relay_controller_addr=1, switch_adapter_addr=10, bind_output=3
[12:59:56][D][kc868_ha.component:057]: found a kc868_ha board, target_relay_controller_addr=1, switch_adapter_addr=10, bind_output=4
[12:59:56][D][kc868_ha.component:057]: found a kc868_ha board, target_relay_controller_addr=1, switch_adapter_addr=10, bind_output=5
[12:59:56][D][kc868_ha.component:057]: found a kc868_ha board, target_relay_controller_addr=1, switch_adapter_addr=10, bind_output=6
[12:59:56][D][binary_sensor:036]: 'binary_sensor 6': Sending state ON
[12:59:56][D][kc868_ha.component:057]: found a kc868_ha board, target_relay_controller_addr=1, switch_adapter_addr=10, bind_output=1
[12:59:56][D][kc868_ha.component:019]: uart bus receive 1:10:0:a:0:6:c:0:0:0:0:0:0:0:0:0:0:6a:2:23:11
[12:59:56][D][kc868_ha.component:030]: uart crc=23:11, calc crc=23:11
[12:59:56][D][kc868_ha.component:046]: dump kc868_ha config, target_relay_controller_addr=1, switch_adapter_addr=10, bind_output=2
[12:59:56][D][kc868_ha.component:046]: dump kc868_ha config, target_relay_controller_addr=1, switch_adapter_addr=10, bind_output=3
[12:59:56][D][kc868_ha.component:046]: dump kc868_ha config, target_relay_controller_addr=1, switch_adapter_addr=10, bind_output=4
[12:59:56][D][kc868_ha.component:046]: dump kc868_ha config, target_relay_controller_addr=1, switch_adapter_addr=10, bind_output=5
[12:59:56][D][kc868_ha.component:046]: dump kc868_ha config, target_relay_controller_addr=1, switch_adapter_addr=10, bind_output=6
[12:59:56][D][kc868_ha.component:046]: dump kc868_ha config, target_relay_controller_addr=1, switch_adapter_addr=10, bind_output=1
[12:59:56][D][kc868_ha.component:057]: found a kc868_ha board, target_relay_controller_addr=1, switch_adapter_addr=10, bind_output=2
[12:59:56][D][kc868_ha.component:057]: found a kc868_ha board, target_relay_controller_addr=1, switch_adapter_addr=10, bind_output=3
[12:59:56][D][kc868_ha.component:057]: found a kc868_ha board, target_relay_controller_addr=1, switch_adapter_addr=10, bind_output=4
[12:59:56][D][kc868_ha.component:057]: found a kc868_ha board, target_relay_controller_addr=1, switch_adapter_addr=10, bind_output=5
[12:59:56][D][kc868_ha.component:057]: found a kc868_ha board, target_relay_controller_addr=1, switch_adapter_addr=10, bind_output=6
[12:59:56][D][binary_sensor:036]: 'binary_sensor 6': Sending state OFF
[12:59:56][D][kc868_ha.component:057]: found a kc868_ha board, target_relay_controller_addr=1, switch_adapter_addr=10, bind_output=1