Smart Home Automation Forum
KC868 H32 - help - needed firmware - Printable Version

+- Smart Home Automation Forum (https://www.kincony.com/forum)
+-- Forum: Technical Support (https://www.kincony.com/forum/forumdisplay.php?fid=1)
+--- Forum: KC868-HxB series Smart Controller (https://www.kincony.com/forum/forumdisplay.php?fid=2)
+--- Thread: KC868 H32 - help - needed firmware (/showthread.php?tid=165)

Pages: 1 2 3 4

RE: KC868 H32 - help - needed firmware - Kam5 - 01-01-2021

(12-31-2020, 10:36 PM)admin Wrote: OK, you can send me the video, we will check. the new firmware include the bootloader function. so when you power on ,begin 5 seconds, there is wait for bootloader, after 5 seconds controller will begin to work. when you update the new firmware of MCU, next time, you can update firmware by RS232 port , not need to use ST-Link cable again.

Dear Admin I sent for You link for video on private message email.


When should be ready new firmware with bootloader for my PLC ?

Thank You.

RE: KC868 H32 - help - needed firmware - admin - 01-01-2021

hello, we have not received your email, you can send again, these days in China are new year holidays, when we begin work, we will have a look.

RE: KC868 H32 - help - needed firmware - Kam5 - 01-04-2021

(01-01-2021, 11:31 PM)admin Wrote: hello, we have not received your email, you can send again, these days in China are new year holidays, when we begin work, we will have a look.


Dear admin please look at this video

Starting PLC K868 H32

I saw that is the problem when I turn off supply on short time for example ~ 1 min brake and powered on - then PLC not activated earlier powered outputs and I couldn't activate mannually outputs.

I must disconnect power supply only for PLC ( others modules are powered) and powered on - in this case start working correctly as You see on video.

--- New remarks  Confused

After long time - few hours of unpowered (PLC , extended board , RS232 duplicator) - and powered again - PLC start working normally. Is is a problem with short unpowered break. Huh

RE: KC868 H32 - help - needed firmware - KinCony Support - 01-05-2021

can you control the KC868-h32 controller by mobile phone??
Let's check it step by step.


no.1

RE: KC868 H32 - help - needed firmware - Kam5 - 01-05-2021

(01-05-2021, 01:16 AM)KinCony Support Wrote: can you control the KC868-h32 controller by mobile phone??
Let's check it step by step.


no.1
Dear Admin I couldn't check yet because I don't have LAN connection. I must prepare wifi router to check that's the communication. In this week I try to do and confirm.

- - Chabeda - 01-18-2021

i have an elite qubo digital and i also want to know if its upgradable or not, on the side there is a yellow sticker with firmware 80, wk 49-14 written on it. The serial number may be CQ2381 but i am not sure

Thank you for you answer

RE: KC868 H32 - help - needed firmware - admin - 01-18-2021

(01-18-2021, 04:33 AM)Chabeda Wrote: i have an elite qubo digital and i also want to know if its upgradable or not, on the side there is a yellow sticker with firmware 80, wk 49-14 written on it. The serial number may be CQ2381 but i am not sure

Thank you for you answer

H32L not need to update firmware.

RE: KC868 H32 - help - needed firmware - matej.radek@seznam.cz - 01-18-2021

Dear Admin please send the latest firmware for my KC868 H32 PLC.
I have an old version of the 32 Channel Expansion Terminal Light Curtain Wall Switch Panel Board that doesn't work. Do I have to buy a new version and do I need to upgrade the firmware?

Please send for my email matej.radek@seznam.cz

Thank You.

RE: KC868 H32 - help - needed firmware - admin - 01-19-2021

ok, i see, now firmware is sent to your email.

RE: KC868 H32 - help - needed firmware - Kam5 - 01-19-2021

(12-31-2020, 10:36 PM)admin Wrote: OK, you can send me the video, we will check. the new firmware include the bootloader function. so when you power on ,begin 5 seconds, there is wait for bootloader, after 5 seconds controller will begin to work. when you update the new firmware of MCU, next time, you can update firmware by RS232 port , not need to use ST-Link cable again.

Dear Admin for my KC868-H32 firmware what You send to me is with bootloader or not yet ? We wait for new relase ?

I notice few times freezing communication by new button switch module under normal working - when I pressed quickly few times wall swith - plc or button switch board stop working - I couldn't switch on/off anything
I notice few times abnormal working wall switch connected to input on button switch - when I press wall switch for example 1st room to on and 2nd time to off - on other room switch on the light Dodgy . It not show on each time but randomly = but always in this same room light on. I checking connections and should be okay.