+- Smart Home Automation Forum (https://www.kincony.com/forum)
+-- Forum: Technical Support (https://www.kincony.com/forum/forumdisplay.php?fid=20)
+--- Forum: KC868-A8S (https://www.kincony.com/forum/forumdisplay.php?fid=24)
+--- Thread: KC868-A8S hotel room demo configure for ESPhome (/showthread.php?tid=1946)
Pages:
1
2
KC868-A8S hotel room demo configure for ESPhome - admin - 05-31-2022
esphome:
name: a8s
platform: ESP32
board: esp32dev
remote_receiver:
pin: 16
dump:
- rc_switch
tolerance: 50%
filter: 250us
idle: 2ms
buffer_size: 2kb
# Example configuration entry for ESP32
i2c:
sda: 4
scl: 5
scan: true
id: bus_a
# Example configuration entry
ethernet:
type: LAN8720
mdc_pin: GPIO23
mdio_pin: GPIO18
clk_mode: GPIO17_OUT
phy_addr: 0
# Optional manual IP
manual_ip:
static_ip: 192.168.1.199
gateway: 192.168.1.1
subnet: 255.255.255.0
# Example configuration entry
pcf8574:
- id: 'pcf8574_hub_out_1' # for output channel 1-8
address: 0x24
- id: 'pcf8574_hub_in_1' # for input channel 1-8
address: 0x22
# Individual outputs
switch:
- platform: gpio
name: "light1"
id: light1
pin:
pcf8574: pcf8574_hub_out_1
number: 0
mode: OUTPUT
inverted: true
- platform: gpio
name: "light2"
id: light2
pin:
pcf8574: pcf8574_hub_out_1
number: 1
mode: OUTPUT
inverted: true
- platform: gpio
name: "light3"
id: light3
pin:
pcf8574: pcf8574_hub_out_1
number: 2
mode: OUTPUT
inverted: true
- platform: gpio
name: "light4"
id: light4
pin:
pcf8574: pcf8574_hub_out_1
number: 3
mode: OUTPUT
inverted: true
- platform: gpio
name: "curtain1-up"
id: relay5
interlock: [relay6]
pin:
pcf8574: pcf8574_hub_out_1
number: 4
mode: OUTPUT
inverted: true
- platform: gpio
name: "curtain1-down"
id: relay6
interlock: [relay5]
pin:
pcf8574: pcf8574_hub_out_1
number: 5
mode: OUTPUT
inverted: true
- platform: gpio
name: "curtain2-up"
id: relay7
interlock: [relay8]
pin:
pcf8574: pcf8574_hub_out_1
number: 6
mode: OUTPUT
inverted: true
- platform: gpio
name: "curtain2-down"
id: relay8
interlock: [relay7]
pin:
pcf8574: pcf8574_hub_out_1
number: 7
mode: OUTPUT
inverted: true
binary_sensor:
- platform: gpio
name: "input1"
on_press:
then:
- switch.toggle: light1
pin:
pcf8574: pcf8574_hub_in_1
number: 0
mode: INPUT
inverted: true
- platform: gpio
name: "input2"
on_press:
then:
- switch.toggle: light2
pin:
pcf8574: pcf8574_hub_in_1
number: 1
mode: INPUT
inverted: true
- platform: gpio
name: "input3"
on_press:
then:
- switch.toggle: light3
pin:
pcf8574: pcf8574_hub_in_1
number: 2
mode: INPUT
inverted: true
- platform: gpio
name: "input4"
on_press:
then:
- switch.toggle: light4
pin:
pcf8574: pcf8574_hub_in_1
number: 3
mode: INPUT
inverted: true
- platform: gpio
name: "input5"
on_press:
then:
- switch.toggle: relay5
pin:
pcf8574: pcf8574_hub_in_1
number: 4
mode: INPUT
inverted: true
- platform: gpio
name: "input6"
on_press:
then:
- switch.toggle: relay6
pin:
pcf8574: pcf8574_hub_in_1
number: 5
mode: INPUT
inverted: true
- platform: gpio
name: "input7"
on_press:
then:
- switch.toggle: relay7
pin:
pcf8574: pcf8574_hub_in_1
number: 6
mode: INPUT
inverted: true
- platform: gpio
name: "input8"
on_press:
then:
- switch.toggle: relay8
pin:
pcf8574: pcf8574_hub_in_1
number: 7
mode: INPUT
inverted: true
- platform: remote_receiver
name: "remoter1"
rc_switch_raw:
code: '001111010111001010111000'
protocol: 1
on_press:
then:
- switch.toggle: light1
filters:
- delayed_off: 200ms
- platform: remote_receiver
name: "remoter2"
rc_switch_raw:
code: '001111010111001010111100'
protocol: 1
on_press:
then:
- switch.toggle: light2
filters:
- delayed_off: 200ms
- platform: remote_receiver
name: "remoter3"
rc_switch_raw:
code: '001111010111001010110100'
protocol: 1
on_press:
then:
- switch.toggle: light3
filters:
- delayed_off: 200ms
- platform: remote_receiver
name: "remoter4"
rc_switch_raw:
code: '001111010111001010111001'
protocol: 1
on_press:
then:
- switch.toggle: light4
filters:
- delayed_off: 200ms
- platform: remote_receiver
name: "remoter5"
rc_switch_raw:
code: '001111010111001010110010'
protocol: 1
on_press:
then:
- switch.toggle: relay5
filters:
- delayed_off: 200ms
- platform: remote_receiver
name: "remoter6"
rc_switch_raw:
code: '001111010111001010110101'
protocol: 1
on_press:
then:
- switch.toggle: relay6
filters:
- delayed_off: 200ms
- platform: remote_receiver
name: "remoter7"
rc_switch_raw:
code: '001111010111001010110001'
protocol: 1
on_press:
then:
- switch.toggle: relay7
filters:
- delayed_off: 200ms
- platform: remote_receiver
name: "remoter8"
rc_switch_raw:
code: '001111010111001010110011'
protocol: 1
on_press:
then:
- switch.toggle: relay8
filters:
- delayed_off: 200ms
- platform: gpio
name: "PIR1"
pin: 14
device_class: motion
on_release:
- script.execute: motion_timer
script:
- id: motion_timer
mode: restart
then:
- delay: 10s
- switch.turn_off: light1
- switch.turn_off: light2
- switch.turn_off: light3
- switch.turn_off: light4
# Enable logging
logger:
# Enable Home Assistant API
api:
RE: KC868-A8S hotel room demo configure for ESPhome - nextclick - 09-30-2022
Thanks for example. Is working.
Is possible add example for AD inputs? I need to show the state of AD inputs (0-5V) in Home Assistant.
And if possible also the procedure for controlling RGBW LEDs from HA
Thanks.
RE: KC868-A8S hotel room demo configure for ESPhome - admin - 10-01-2022
# Example configuration entry
sensor:
- platform: adc
pin: 36
name: "analog-1"
update_interval: 10s
attenuation: 11db
- platform: adc
pin: 39
name: "analog-2"
update_interval: 10s
attenuation: 11db
- platform: adc
pin: 34
name: "analog-3"
update_interval: 10s
attenuation: 11db
- platform: adc
pin: 35
name: "analog-4"
update_interval: 10s
attenuation: 11db
RE: KC868-A8S hotel room demo configure for ESPhome - JCh - 12-12-2022
Is it possible to add an example for measuring 4-20mA on AI 3-4? Is it possible to connect a 24V sensor to this input? Thanks
RE: KC868-A8S hotel room demo configure for ESPhome - admin - 12-13-2022
esphome config line as same as measuring dc 0-5v sensor. if you connect with 4-20mA signal to board, also will convert "current" to "voltage" value.
now board input level MAX is dc12v , if you want to use 24v sensor, you can convert to dc12v then connect to digital input port.
RE: KC868-A8S hotel room demo configure for ESPhome - benlouisv@gmail.com - 03-07-2023
Can you maby assist me how to connect a 4-20ma pressure sensor to the unit?
Sensor info
Supply 9-36vdc
Output 4-20ma
Range 0-5bar
RE: KC868-A8S hotel room demo configure for ESPhome - admin - 03-07-2023
the default circuit is use for analog input 0-5v. if you want to test with 4-20mA, need replace two resistance value. such as here is sample of ADC1, replace R70=0 ohm R72=150 ohm
RE: KC868-A8S hotel room demo configure for ESPhome - benlouisv@gmail.com - 03-08-2023
Sso for the A6 model all Analogue inputs are 0-5v defaut. can I replace all 4 inputs reaiators to use 4 x 4-20ma sensors?
RE: KC868-A8S hotel room demo configure for ESPhome - admin - 03-08-2023
yes, you are right.
RE: KC868-A8S hotel room demo configure for ESPhome - benlouisv@gmail.com - 03-08-2023
Do you have models that can use 4-20ma sensors without modifications