KC868-A16 - Different digital Output modes - Printable Version +- Smart Home Automation Forum (https://www.kincony.com/forum) +-- Forum: Technical Support (https://www.kincony.com/forum/forumdisplay.php?fid=1) +--- Forum: DIY Project (https://www.kincony.com/forum/forumdisplay.php?fid=3) +--- Thread: KC868-A16 - Different digital Output modes (/showthread.php?tid=2804) |
KC868-A16 - Different digital Output modes - oxedgar - 04-14-2023 Hello, I try to get KCS-Firmware to work has i want... I have one output to need to work in two modes ... the first is normal On-OFF toggle with one input triggered (this work fine) The the second mode is to delayed this same output if i trigger another input (this do not work) The result is to provide one wall button to ON Off Light and for the same light one motion PIR not temporised to work with specific delay set in this smart controller! Can i make this with KCS firmware? RE: KC868-A16 - Different digital Output modes - admin - 04-14-2023 do you mean: use by two INPUT mode: 1. input short with GND, output action right now. 2. input short with GND and hold on some second, then output action run. is that right? RE: KC868-A16 - Different digital Output modes - oxedgar - 04-14-2023 Not exactly! here are more details: I want to use a button and a Pir to turn on a lamp. But I want the pir to turn on the lamp on a timed basis. However, I may also need to light the lamp for a long time. hence I need a button to turn it on and off! Here is the context: Terminal Device Function DI1 Button DO1 = ON-OFF DI2 PIR DO1 = Delay 2 minutes DO1 Relay I would like to do it intelligently without necessarily using two outputs with one timed and the other ON-OFF wired in parallel! Is it possible? RE: KC868-A16 - Different digital Output modes - admin - 04-15-2023 Terminal Device Function DI1 Button DO1 = ON-OFF DI2 PIR DO1 = Delay 2 minutes DO1 Relay do these function by two different DI, no problem with "KCS" fimrware, you can try. i understand you now. RE: KC868-A16 - Different digital Output modes - oxedgar - 04-16-2023 can you tell me how can i make this? When i put the delay on DO1 all times the delay occurs! is not like i want!?! I found one way but i lose one output by delayed outputs i need! in case of DO1, i have connected SSR. In Parallel i have connected output Do11 with one Diode 1N4001 and i have setted my tempo on Do11 and no tempo on DO1. This is not very fun but it is working ! Tell me if you have another way to make this with KCS? RE: KC868-A16 - Different digital Output modes - admin - 04-17-2023 do you use the newest "KCS" firmware v1.0.24? because it have updated: https://www.kincony.com/forum/showthread.php?tid=2764 2. Fix timer bug for different channel reset problem. now every channel have own timer. RE: KC868-A16 - Different digital Output modes - oxedgar - 04-17-2023 (04-17-2023, 12:22 AM)admin Wrote: do you use the newest "KCS" firmware v1.0.24? because it have updated: Yes it is the latest version. I found one bug on this version... the timezone not work! i have +1 tz but i need to set it in +8 tz to see the right time in index page! RE: KC868-A16 - Different digital Output modes - admin - 04-17-2023 we will feedback to software engineer. RE: KC868-A16 - Different digital Output modes - KinCony Support - 04-17-2023 (04-14-2023, 06:13 PM)oxedgar Wrote: Not exactly! here are more details: POST a image about your settings |