+- Smart Home Automation Forum (https://www.kincony.com/forum)
+-- Forum: Technical Support (https://www.kincony.com/forum/forumdisplay.php?fid=20)
+--- Forum: KC868-AG / AG Pro / AG8 (https://www.kincony.com/forum/forumdisplay.php?fid=30)
+--- Thread: ESPHome yaml demo file for AG8 IR controller (/showthread.php?tid=5889)
ESPHome yaml demo file for AG8 IR controller - admin - 06-14-2024
Code:
esphome:
name: ag8
friendly_name: ag8
platformio_options:
board_build.flash_mode: dio
esp32:
board: esp32-s3-devkitc-1
framework:
type: esp-idf
sdkconfig_options:
SOC_RMT_SUPPORT_RX_PINGPONG: "n"
# Enable logging
logger:
hardware_uart: USB_SERIAL_JTAG
# Enable Home Assistant API
api:
encryption:
key: "dolIFOGZiGF8GT9wSJVBuoNzVQSHanaieBBbRcj1t48="
ethernet:
type: W5500
clk_pin: GPIO42
mosi_pin: GPIO43
miso_pin: GPIO44
cs_pin: GPIO41
interrupt_pin: GPIO2
reset_pin: GPIO1
remote_receiver:
pin: 48
rmt_channel: 4
dump: all
remote_transmitter:
- id: ir1
pin: 9
carrier_duty_percent: 50%
- id: ir2
pin: 10
carrier_duty_percent: 50%
- id: ir3
pin: 11
carrier_duty_percent: 50%
- id: ir4
pin: 12
carrier_duty_percent: 50%
# - id: ir5
# pin: 13
# carrier_duty_percent: 50%
# - id: ir6
# pin: 14
# carrier_duty_percent: 50%
# - id: ir7
# pin: 21
# carrier_duty_percent: 50%
# - id: ir8
# pin: 47
# carrier_duty_percent: 50%
switch:
- platform: template
name: IR-Send1
turn_on_action:
- remote_transmitter.transmit_panasonic:
transmitter_id: ir1
address: 0x4004
command: 0x8140DFA2
- platform: template
name: IR-Send2
turn_on_action:
- remote_transmitter.transmit_panasonic:
transmitter_id: ir2
address: 0x4004
command: 0x8140DFA2
- platform: template
name: IR-Send3
turn_on_action:
- remote_transmitter.transmit_panasonic:
transmitter_id: ir3
address: 0x4004
command: 0x8140DFA2
- platform: template
name: IR-Send4
turn_on_action:
- remote_transmitter.transmit_panasonic:
transmitter_id: ir4
address: 0x4004
command: 0x8140DFA2
# - platform: template
# name: IR-Send5
# turn_on_action:
# - remote_transmitter.transmit_panasonic:
# transmitter_id: ir5
# address: 0x4004
# command: 0x8140DFA2
# - platform: template
# name: IR-Send6
# turn_on_action:
# - remote_transmitter.transmit_panasonic:
# transmitter_id: ir6
# address: 0x4004
# command: 0x8140DFA2
# - platform: template
# name: IR-Send7
# turn_on_action:
# - remote_transmitter.transmit_panasonic:
# transmitter_id: ir7
# address: 0x4004
# command: 0x8140DFA2
# - platform: template
# name: IR-Send8
# turn_on_action:
# - remote_transmitter.transmit_panasonic:
# transmitter_id: ir8
# address: 0x4004
# command: 0x8140DFA2
- platform: uart
uart_id: uart_485
name: "RS485 Button"
data: [0x11, 0x22, 0x33, 0x44, 0x55]
- platform: uart
uart_id: uart_232
name: "RS232 Button"
data: "RS232-test"
uart:
- id: uart_485
baud_rate: 9600
debug:
direction: BOTH
dummy_receiver: true
after:
timeout: 10ms
tx_pin: 18
rx_pin: 8
- id: uart_232
baud_rate: 9600
debug:
direction: BOTH
dummy_receiver: true
after:
timeout: 10ms
sequence:
- lambda: UARTDebug::log_string(direction, bytes);
tx_pin: 17
rx_pin: 16
binary_sensor:
- platform: gpio
name: "IO15"
pin:
number: 15
inverted: true
mode:
input: true
pullup: true
- platform: gpio
name: "IO38"
pin:
number: 38
inverted: true
mode:
input: true
pullup: true
- platform: gpio
name: "IO39"
pin:
number: 39
inverted: true
mode:
input: true
pullup: true
- platform: gpio
name: "IO40"
pin:
number: 40
inverted: true
mode:
input: true
pullup: true
web_server:
port: 80demo yaml for control Apple TV:
Code:
esphome:
name: ag8
friendly_name: ag8
platformio_options:
board_build.flash_mode: dio
esp32:
board: esp32-s3-devkitc-1
framework:
type: esp-idf
sdkconfig_options:
SOC_RMT_SUPPORT_RX_PINGPONG: "n"
# Enable logging
logger:
hardware_uart: USB_SERIAL_JTAG
# Enable Home Assistant API
api:
encryption:
key: "dolIFOGZiGF8GT9wSJVBuoNzVQSHanaieBBbRcj1t48="
ethernet:
type: W5500
clk_pin: GPIO42
mosi_pin: GPIO43
miso_pin: GPIO44
cs_pin: GPIO41
interrupt_pin: GPIO2
reset_pin: GPIO1
remote_receiver:
pin: 48
rmt_channel: 4
dump: all
remote_transmitter:
- id: ir1
pin: 9
carrier_duty_percent: 50%
- id: ir2
pin: 10
carrier_duty_percent: 50%
- id: ir3
pin: 11
carrier_duty_percent: 50%
- id: ir4
pin: 12
carrier_duty_percent: 50%
# - id: ir5
# pin: 13
# carrier_duty_percent: 50%
# - id: ir6
# pin: 14
# carrier_duty_percent: 50%
# - id: ir7
# pin: 21
# carrier_duty_percent: 50%
# - id: ir8
# pin: 47
# carrier_duty_percent: 50%
switch:
- platform: template
name: IR-Send1
turn_on_action:
- remote_transmitter.transmit_pronto:
transmitter_id: ir1
data: "0000 006C 0022 0002 015B 00AD 0016 0041 0016 0016 0016 0041 0016 0016 0016 0016 0016 0041 0016 0041 0016 0041 0016 0041 0016 0041 0016 0041 0016 0016 0016 0016 0016 0016 0016 0016 0016 0041 0016 0041 0016 0041 0016 0041 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0041 0016 0041 0016 0041 0016 0041 0016 0041 0016 0041 0016 0041 0016 0575 015B 0057 0016 0E6C"
- platform: template
name: IR-Send2
turn_on_action:
- remote_transmitter.transmit_pronto:
transmitter_id: ir2
data: "0000 006C 0022 0002 015B 00AD 0016 0041 0016 0016 0016 0041 0016 0016 0016 0016 0016 0041 0016 0041 0016 0041 0016 0041 0016 0041 0016 0041 0016 0016 0016 0016 0016 0016 0016 0016 0016 0041 0016 0016 0016 0016 0016 0016 0016 0041 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0041 0016 0041 0016 0041 0016 0041 0016 0041 0016 0041 0016 0041 0016 05CB 015B 0057 0016 0E6C"
- platform: template
name: IR-Send3
turn_on_action:
- remote_transmitter.transmit_pronto:
transmitter_id: ir3
data: "0000 006C 0022 0002 015B 00AD 0016 0041 0016 0016 0016 0041 0016 0016 0016 0016 0016 0041 0016 0041 0016 0041 0016 0041 0016 0041 0016 0041 0016 0016 0016 0016 0016 0016 0016 0016 0016 0041 0016 0016 0016 0016 0016 0041 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0041 0016 0041 0016 0041 0016 0041 0016 0041 0016 0041 0016 0041 0016 05CB 015B 0057 0016 0E6C"
- platform: template
name: IR-Send4
turn_on_action:
- remote_transmitter.transmit_pronto:
transmitter_id: ir4
data: "0000 006C 0022 0002 015B 00AD 0016 0041 0016 0016 0016 0041 0016 0016 0016 0016 0016 0041 0016 0041 0016 0041 0016 0041 0016 0041 0016 0041 0016 0016 0016 0016 0016 0016 0016 0016 0016 0041 0016 0016 0016 0041 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0041 0016 0041 0016 0041 0016 0041 0016 0041 0016 0041 0016 0041 0016 05CB 015B 0057 0016 0E6C"
# - platform: template
# name: IR-Send5
# turn_on_action:
# - remote_transmitter.transmit_panasonic:
# transmitter_id: ir5
# address: 0x4004
# command: 0x8140DFA2
# - platform: template
# name: IR-Send6
# turn_on_action:
# - remote_transmitter.transmit_panasonic:
# transmitter_id: ir6
# address: 0x4004
# command: 0x8140DFA2
# - platform: template
# name: IR-Send7
# turn_on_action:
# - remote_transmitter.transmit_panasonic:
# transmitter_id: ir7
# address: 0x4004
# command: 0x8140DFA2
# - platform: template
# name: IR-Send8
# turn_on_action:
# - remote_transmitter.transmit_panasonic:
# transmitter_id: ir8
# address: 0x4004
# command: 0x8140DFA2
- platform: uart
uart_id: uart_485
name: "RS485 Button"
data: [0x11, 0x22, 0x33, 0x44, 0x55]
- platform: uart
uart_id: uart_232
name: "RS232 Button"
data: "RS232-test"
uart:
- id: uart_485
baud_rate: 9600
debug:
direction: BOTH
dummy_receiver: true
after:
timeout: 10ms
tx_pin: 18
rx_pin: 8
- id: uart_232
baud_rate: 9600
debug:
direction: BOTH
dummy_receiver: true
after:
timeout: 10ms
sequence:
- lambda: UARTDebug::log_string(direction, bytes);
tx_pin: 17
rx_pin: 16
binary_sensor:
- platform: gpio
name: "IO15"
pin:
number: 15
inverted: true
mode:
input: true
pullup: true
- platform: gpio
name: "IO38"
pin:
number: 38
inverted: true
mode:
input: true
pullup: true
- platform: gpio
name: "IO39"
pin:
number: 39
inverted: true
mode:
input: true
pullup: true
- platform: gpio
name: "IO40"
pin:
number: 40
inverted: true
mode:
input: true
pullup: true
web_server:
port: 80Node: ESP32-S3 chip support 4 channel IR sender work at the same time. here is details by ESPHome webpage:
https://esphome.io/components/remote_transmitter.html