K868-Uair proper GPIO assignation ?

[vincen]

Hi

I'm tyring to use a K868-Uair with ESPHome but I have some problems ! According at Kincony ducomentation it should GPIO32 and 33 to control RGB LEDs of bottom ring and vertical bar ! Unhappy these two GPIOs are doing exactly the same thing: control the ring only and only 3 LEDs of it
Someone has the proper GPIO configuration of that board ?
Noticed also that the Dallas temperature sensor is a chinese copy I think as it's 4/5° offset of other temperature sensors I have in the room

Code used so far in ESPHome for LEDs:

Code:

light:
  - platform: neopixelbus
    type: GRB
    variant: WS2812X
    pin: GPIO33
    num_leds: 4
    name: "Barre"
  - platform: neopixelbus
    type: GRB
    variant: WS2812X
    pin: GPIO32
    num_leds: 4
    name: "Ring"

Thanks for help

Vincèn

[admin]

esphome:
  name: kc868-uair
  platform: ESP32
  board: esp32dev

# Enable logging
logger:

# Enable Home Assistant API
api:

ota:
  password: "978e66f878ed5041b830cfb427393c79"

wifi:
  ssid: "KinCony"  # your wifi router ssid
  password: "12345678"  # your wifi password

  # Enable fallback hotspot (captive portal) in case wifi connection fails
  ap:
    ssid: "Kc868-Uair Fallback Hotspot"
    password: "FbTxCLlbDvbO"

captive_portal:

# follow configure use for DS18B20 temperature sensor, SHT30 temperature and humidity sensor. WS2812B RGB LEDs.
i2c:
  sda: 4
  scl: 16
  scan: true
  id: bus_a

         
# Example configuration entry
dallas:
  - pin: GPIO27
    update_interval: 15s

# Individual sensors
sensor:
  - platform: dallas
    address: 0xC000000004D81528  # your DS18B20 address
    name: "internal Temperature"
 
# Example configuration entry
  - platform: sht3xd
    temperature:
      name: "extend Temperature"
    humidity:
      name: "extend Humidity"
    address: 0x44
    update_interval: 15s
 
light:
  - platform: fastled_clockless
    chipset: WS2812B
    pin: GPIO32    # Pin Define connected with LED strip
    num_leds: 4  #LEDs number
    rgb_order: GRB
    name: "Uair-Bottom-LED"
    effects:
      - addressable_rainbow:        ##defined 7 effects styles
      - addressable_color_wipe:
      - addressable_scan:
      - addressable_twinkle:
      - addressable_random_twinkle:
      - addressable_fireworks:
      - addressable_flicker:

  - platform: fastled_clockless
    chipset: WS2812B
    pin: GPIO33    # Pin Define connected with LED strip
    num_leds: 1  #LEDs number
    rgb_order: RGB
    name: "Uair-Vertical-LED"
    effects:
      - addressable_rainbow:        ##defined 7 effects styles
      - addressable_color_wipe:
      - addressable_scan:
      - addressable_twinkle:
      - addressable_random_twinkle:
      - addressable_fireworks:
      - addressable_flicker:

[admin]

Hi

I'm tyring to use a K868-Uair with ESPHome but I have some problems ! According at Kincony ducomentation it should GPIO32 and 33 to control RGB LEDs of bottom ring and vertical bar ! Unhappy these two GPIOs are doing exactly the same thing: control the ring only and only 3 LEDs of it
Someone has the proper GPIO configuration of that board ?
Noticed also that the Dallas temperature sensor is a chinese copy I think as it's 4/5° offset of other temperature sensors I have in the room

Code used so far in ESPHome for LEDs:

Code:

light:
  - platform: neopixelbus
    type: GRB
    variant: WS2812X
    pin: GPIO33
    num_leds: 4
    name: "Barre"
  - platform: neopixelbus
    type: GRB
    variant: WS2812X
    pin: GPIO32
    num_leds: 4
    name: "Ring"

Thanks for help

Vincèn

GPIO33 use for 1 LED
GPIO32 use for 4 LED

[vincen]

Hi

I'm tyring to use a K868-Uair with ESPHome but I have some problems ! According at Kincony ducomentation it should GPIO32 and 33 to control RGB LEDs of bottom ring and vertical bar ! Unhappy these two GPIOs are doing exactly the same thing: control the ring only and only 3 LEDs of it
Someone has the proper GPIO configuration of that board ?
Noticed also that the Dallas temperature sensor is a chinese copy I think as it's 4/5° offset of other temperature sensors I have in the room

Code used so far in ESPHome for LEDs:

Code:

light:
  - platform: neopixelbus
    type: GRB
    variant: WS2812X
    pin: GPIO33
    num_leds: 4
    name: "Barre"
  - platform: neopixelbus
    type: GRB
    variant: WS2812X
    pin: GPIO32
    num_leds: 4
    name: "Ring"

Thanks for help

Vincèn

GPIO33 use for 1 LED
GPIO32 use for 4 LED

Thanks for code it works this way but it's using old RGB implementation mode of ESPHome

[vincen]

In fact the device has a hardware issue as one of the ring LED is wired with bar so only 3 LEDs of ring work together, the other one works with bar which kills the visual effect of the ring !! Are you aware of that problem on the device ??

[admin]

In fact the device has a hardware issue as one of the ring LED is wired with bar so only 3 LEDs of ring work together, the other one works with bar which kills the visual effect of the ring !! Are you aware of that problem on the device ??


no, 4 LEDs work together with ring LED. another one LED is indepentant. here is diagram, you can see details.
   

[vincen]

no, 4 LEDs work together with ring LED. another one LED is indepentant. here is diagram, you can see details.

Thanks for the schematics but it doesn't correspond with reality ! Have a look at my picture you can clearly one of the LED is not following the other ones on ring but the ones of bar

[admin]

do you use my code directly? or changed something?

[vincen]

do you use my code directly? or changed something?

I use your code nearly without modifications, here it is:

Code:

substitutions:
  friendly_name: kincony-netatmo

esphome:
  name: $friendly_name

esp32:
  board: esp32dev
  framework:
    type: arduino

logger:

web_server:

ota:

wifi:
  networks:
  - ssid: !secret wifi
    password: !secret wifi_passwd
  - ssid: !secret wifi_puppy
    password: !secret wifi_puppy_passwd
  ap:
    ssid: $friendly_name

captive_portal:

api:
  reboot_timeout: 120min

#i2c:
#  sda: 4
#  scl: 16
#  scan: true
#  id: bus_a
 
dallas:
  - pin: GPIO27
    update_interval: 15s

sensor:
  - platform: dallas
    address: 0x0800000004680128
    name: "Temperature"

light:
  - platform: fastled_clockless
    chipset: WS2812B
    pin: GPIO32    # Pin Define connected with LED strip
    num_leds: 4  #LEDs number
    rgb_order: GRB
    name: "Ring"
    effects:
      - addressable_rainbow:        ##defined 7 effects styles
      - addressable_color_wipe:
      - addressable_scan:
      - addressable_twinkle:
      - addressable_random_twinkle:
      - addressable_fireworks:
      - addressable_flicker:

  - platform: fastled_clockless
    chipset: WS2812B
    pin: GPIO33    # Pin Define connected with LED strip
    num_leds: 1  #LEDs number
    rgb_order: RGB
    name: "Bar"
    effects:
      - addressable_rainbow:        ##defined 7 effects styles
      - addressable_color_wipe:
      - addressable_scan:
      - addressable_twinkle:
      - addressable_random_twinkle:
      - addressable_fireworks:
      - addressable_flicker:

[admin]

i think you need to check software, hardware is no problem, here is some our demo images.