KC868-1U-ha-config.txt (Size: 5.76 KB / Downloads: 163)
esphome:
name: 1u
platform: ESP32
board: esp32dev
remote_receiver:
pin: 13
dump:
- rc_switch
tolerance: 50%
filter: 250us
idle: 2ms
buffer_size: 2kb
# Example configuration entry for ESP32
i2c:
sda: 4
scl: 16
scan: true
id: bus_a
# Example configuration entry
ethernet:
type: LAN8720
mdc_pin: GPIO23
mdio_pin: GPIO18
clk_mode: GPIO17_OUT
phy_addr: 0
# Optional manual IP
# manual_ip:
# static_ip: 192.168.1.199
# gateway: 192.168.1.1
# subnet: 255.255.255.0
# Example configuration entry
pcf8574:
- id: 'pcf8574_hub_out_1' # for output channel 1-8
address: 0x24
- id: 'pcf8574_hub_in_1' # for input channel 1-8
address: 0x22
# Individual outputs
switch:
- platform: gpio
name: "light1"
id: light1
pin:
pcf8574: pcf8574_hub_out_1
number: 0
mode: OUTPUT
inverted: true
- platform: gpio
name: "light2"
id: light2
pin:
pcf8574: pcf8574_hub_out_1
number: 1
mode: OUTPUT
inverted: true
- platform: gpio
name: "light3"
id: light3
pin:
pcf8574: pcf8574_hub_out_1
number: 2
mode: OUTPUT
inverted: true
- platform: gpio
name: "light4"
id: light4
pin:
pcf8574: pcf8574_hub_out_1
number: 3
mode: OUTPUT
inverted: true
- platform: gpio
name: "light5"
id: light5
pin:
pcf8574: pcf8574_hub_out_1
number: 4
mode: OUTPUT
inverted: true
- platform: gpio
name: "light6"
id: light6
pin:
pcf8574: pcf8574_hub_out_1
number: 5
mode: OUTPUT
inverted: true
- platform: gpio
name: "light7"
id: light7
pin:
pcf8574: pcf8574_hub_out_1
number: 6
mode: OUTPUT
inverted: true
- platform: gpio
name: "light8"
id: light8
pin:
pcf8574: pcf8574_hub_out_1
number: 7
mode: OUTPUT
inverted: true
binary_sensor:
- platform: gpio
name: "input1"
on_press:
then:
- switch.toggle: light1
pin:
pcf8574: pcf8574_hub_in_1
number: 0
mode: INPUT
inverted: true
- platform: gpio
name: "input2"
on_press:
then:
- switch.toggle: light2
pin:
pcf8574: pcf8574_hub_in_1
number: 1
mode: INPUT
inverted: true
- platform: gpio
name: "input3"
on_press:
then:
- switch.toggle: light3
pin:
pcf8574: pcf8574_hub_in_1
number: 2
mode: INPUT
inverted: true
- platform: gpio
name: "input4"
on_press:
then:
- switch.toggle: light4
pin:
pcf8574: pcf8574_hub_in_1
number: 3
mode: INPUT
inverted: true
- platform: gpio
name: "input5"
on_press:
then:
- switch.toggle: light5
pin:
pcf8574: pcf8574_hub_in_1
number: 4
mode: INPUT
inverted: true
- platform: gpio
name: "input6"
on_press:
then:
- switch.toggle: light6
pin:
pcf8574: pcf8574_hub_in_1
number: 5
mode: INPUT
inverted: true
- platform: gpio
name: "input7"
on_press:
then:
- switch.toggle: light7
pin:
pcf8574: pcf8574_hub_in_1
number: 6
mode: INPUT
inverted: true
- platform: gpio
name: "input8"
on_press:
then:
- switch.toggle: light8
pin:
pcf8574: pcf8574_hub_in_1
number: 7
mode: INPUT
inverted: true
- platform: remote_receiver
name: "remoter1"
rc_switch_raw:
code: '001111010111001010111000'
protocol: 1
on_press:
then:
- switch.toggle: light1
filters:
- delayed_off: 200ms
- platform: remote_receiver
name: "remoter2"
rc_switch_raw:
code: '001111010111001010111100'
protocol: 1
on_press:
then:
- switch.toggle: light2
filters:
- delayed_off: 200ms
- platform: remote_receiver
name: "remoter3"
rc_switch_raw:
code: '001111010111001010110100'
protocol: 1
on_press:
then:
- switch.toggle: light3
filters:
- delayed_off: 200ms
- platform: remote_receiver
name: "remoter4"
rc_switch_raw:
code: '001111010111001010111001'
protocol: 1
on_press:
then:
- switch.toggle: light4
filters:
- delayed_off: 200ms
- platform: remote_receiver
name: "remoter5"
rc_switch_raw:
code: '001111010111001010110010'
protocol: 1
on_press:
then:
- switch.toggle: light5
filters:
- delayed_off: 200ms
- platform: remote_receiver
name: "remoter6"
rc_switch_raw:
code: '001111010111001010110101'
protocol: 1
on_press:
then:
- switch.toggle: light6
filters:
- delayed_off: 200ms
- platform: remote_receiver
name: "remoter7"
rc_switch_raw:
code: '001111010111001010110001'
protocol: 1
on_press:
then:
- switch.toggle: light7
filters:
- delayed_off: 200ms
- platform: remote_receiver
name: "remoter8"
rc_switch_raw:
code: '001111010111001010110011'
protocol: 1
on_press:
then:
- switch.toggle: light8
filters:
- delayed_off: 200ms
# Enable logging
logger:
# Enable Home Assistant API
api:
dallas:
- pin: 14
update_interval: 5s
sensor:
- platform: dallas
address: 0xa538cee908646128
name: "1U Temperature"