Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Tuya adapter V2 arduino source code - RS485 temperature humidity sensor
#1
let your own RS485 temperature and humidity sensor can work with Tuya app, so that can remote monitor sensor data and make AUTOMATION by Tuya app via internet.
   
         
   
arduino source code donwload: 
.zip   Tuya_AdapterV2_RS485_Temper_Hum.zip (Size: 1.98 KB / Downloads: 80)
Code:
#include <ModbusMaster.h>
#include <Arduino.h>
#include <TuyaWifi.h>
#include "HardwareSerial.h"
//---------RS485 setting
#define DEBUG   1

#define SERIAL_BAUD   9600
#define RX_PIN    32
#define TX_PIN    33
#define SERIAL_NUM  2
#define SLAVE_ADDR  1
#define READ_ADDR  0
#define READ_NUM   2 

HardwareSerial My485Serial(SERIAL_NUM);
ModbusMaster node;
uint16_t rcv_buf[READ_NUM] = {0};
float get_value[2] = {0.0};

/* Current device DP values */
int temperature = 0;
int humidity = 0;

static void ReadInputRegs(void)
{
  uint8_t result = node.readInputRegisters(READ_ADDR, READ_NUM);
  if (result == node.ku8MBSuccess) {//if communicate successful then
    #if DEBUG
    Serial1.print("Result:"); 
    #endif
   
    for (uint8_t j = 0; j < READ_NUM; j++)
    {
      rcv_buf[j] = node.getResponseBuffer(j);
      #if 0 ///just for debug.
      Serial1.print(" 0x");
      Serial1.print( rcv_buf[j], HEX );//display data in hex.
      #endif
    }
    get_value[0] = rcv_buf[0]/10;///huminity
    get_value[1] = rcv_buf[1]/10;///temperature

    temperature = rcv_buf[0];
    humidity = get_value[1];
   
    #if DEBUG
    Serial1.print("humi.<"); 
    Serial1.print(get_value[1]);
    Serial1.print("%>");
    Serial1.print(" temp.<"); 
    Serial1.print(get_value[0]);
    Serial1.println("°c>");
    #endif

    //delay(300);
  }
  else
  {
    node.clearResponseBuffer();
  }
}

//---RS485 setting end----

TuyaWifi my_device;



/* Current LED status */
unsigned char led_state = 0;
/* Connect network button pin */
int key_pin = 25;

/* Data point define */
#define DPID_TEMP_CURRENT     1
#define DPID_HUMIDITY_CURRENT 2

#define LED_WiFi  26
//#define LED_User  33



/* Stores all DPs and their types. PS: array[][0]:dpid, array[][1]:dp type.
*                                     dp type(TuyaDefs.h) : DP_TYPE_RAW, DP_TYPE_BOOL, DP_TYPE_VALUE, DP_TYPE_STRING, DP_TYPE_ENUM, DP_TYPE_BITMAP
*/
unsigned char dp_array[][2] =
{
  {DPID_TEMP_CURRENT, DP_TYPE_VALUE},
  {DPID_HUMIDITY_CURRENT, DP_TYPE_VALUE},
};

unsigned char pid[] = {"dpyditdgaadmqw8m"};
unsigned char mcu_ver[] = {"1.0.0"};

/* last time */
unsigned long last_time = 0;

void setup()
{

  My485Serial.begin(SERIAL_BAUD, SERIAL_8N1, RX_PIN, TX_PIN); //RS485 serial port
  node.begin(SLAVE_ADDR,My485Serial);
  Serial.begin(9600,SERIAL_8N1,22,19);  //Tuya module serial port
  Serial1.begin(115200,SERIAL_8N1,3,1);   //USB serial port

 
  // Serial with tuyawifi
 
 

  //Initialize led port, turn off led.
  pinMode(LED_WiFi, OUTPUT);
  digitalWrite(LED_WiFi, LOW);

/*  pinMode(LED_User, OUTPUT);
  digitalWrite(LED_User, LOW);*/

  //Initialize networking keys.
  pinMode(key_pin, INPUT_PULLUP);

  //Enter the PID and MCU software version
  my_device.init(pid, mcu_ver);
  //incoming all DPs and their types array, DP numbers
  my_device.set_dp_cmd_total(dp_array, 2);
  //register DP download processing callback function
  my_device.dp_process_func_register(dp_process);
  //register upload all DP callback function
  my_device.dp_update_all_func_register(dp_update_all);
 
  //delay(300);
  last_time = millis();
}

void loop()
{
  ReadInputRegs();  // read RS485 sensor
  my_device.uart_service();

  //Enter the connection network mode when Pin7 is pressed.
  if (digitalRead(key_pin) == LOW) {
    delay(80);
    if (digitalRead(key_pin) == LOW) {
      my_device.mcu_set_wifi_mode(SMART_CONFIG);
    }
  }
  /* LED blinks when network is being connected */
  if ((my_device.mcu_get_wifi_work_state() != WIFI_LOW_POWER) && (my_device.mcu_get_wifi_work_state() != WIFI_CONN_CLOUD) && (my_device.mcu_get_wifi_work_state() != WIFI_SATE_UNKNOW)) {
    if (millis()- last_time >= 500) {
      last_time = millis();

      if (led_state == LOW) {
        led_state = HIGH;
      } else {
        led_state = LOW;
      }
      digitalWrite(LED_WiFi, led_state);
    }
  }

  /* report the temperature and humidity */
  if ((my_device.mcu_get_wifi_work_state() == WIFI_CONNECTED) || (my_device.mcu_get_wifi_work_state() == WIFI_CONN_CLOUD)) {
    my_device.mcu_dp_update(DPID_TEMP_CURRENT, temperature, 1);
    my_device.mcu_dp_update(DPID_HUMIDITY_CURRENT, humidity, 1);
  }

  delay(1000);
}

/**
* @description: DP download callback function.
* @param {unsigned char} dpid
* @param {const unsigned char} value
* @param {unsigned short} length
* @return {unsigned char}
*/
unsigned char dp_process(unsigned char dpid,const unsigned char value[], unsigned short length)
{
  /* all DP only report */
  return TY_SUCCESS;
}

/**
* @description: Upload all DP status of the current device.
* @param {*}
* @return {*}
*/
void dp_update_all(void)
{
  my_device.mcu_dp_update(DPID_TEMP_CURRENT, temperature, 1);
  my_device.mcu_dp_update(DPID_HUMIDITY_CURRENT, humidity, 1);
}
Reply


Messages In This Thread
Tuya adapter V2 arduino source code - RS485 temperature humidity sensor - by admin - 05-06-2024, 01:35 AM

Forum Jump:


Users browsing this thread:
1 Guest(s)