Smart Home Automation Forum › Technical Support › KC868-A8M
KC868-A8M configure yaml for ESPhome

Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Threaded Mode
KC868-A8M configure yaml for ESPhome
admin Offline
Administrator
*******
Posts: 6,324
Threads: 808
Joined: Oct 2020
Reputation: 155
#1
04-14-2023, 02:10 AM (This post was last modified: 04-24-2023, 01:08 AM by admin.)
esphome:
  name: a8m
  platform: ESP32
  board: esp32dev
 
 
remote_receiver:
  pin: 16
  dump:
    - rc_switch
  tolerance: 50%
  filter: 250us
  idle: 2ms
  buffer_size: 2kb



# Example configuration entry for ESP32
i2c:
  sda: 5
  scl: 4
  scan: true
  id: bus_a


# Example configuration entry
ethernet:
  type: LAN8720
  mdc_pin: GPIO23
  mdio_pin: GPIO18
  clk_mode: GPIO17_OUT
  phy_addr: 0

  # Optional manual IP
  manual_ip:
    static_ip: 192.168.1.199
    gateway: 192.168.1.1
    subnet: 255.255.255.0 


# Example configuration entry
pcf8574:
  - id: 'pcf8574_hub_out_1'  # for output channel 1-8
    address: 0x24

  - id: 'pcf8574_hub_in_1'  # for input channel 1-8
    address: 0x22

# Individual outputs
switch:
  - platform: gpio
    name: "light1"
    id: light1
    pin:
      pcf8574: pcf8574_hub_out_1
      number: 0
      mode: OUTPUT
      inverted: true

  - platform: gpio
    name: "light2"
    id: light2
    pin:
      pcf8574: pcf8574_hub_out_1
      number: 1
      mode: OUTPUT
      inverted: true
     
  - platform: gpio
    name: "light3"
    id: light3
    pin:
      pcf8574: pcf8574_hub_out_1
      number: 2
      mode: OUTPUT
      inverted: true
     
  - platform: gpio
    name: "light4"
    id: light4
    pin:
      pcf8574: pcf8574_hub_out_1
      number: 3
      mode: OUTPUT
      inverted: true
     
  - platform: gpio
    name: "curtain1-up"
    id: relay5
    pin:
      pcf8574: pcf8574_hub_out_1
      number: 4
      mode: OUTPUT
      inverted: true
     
     
     
  - platform: gpio
    name: "curtain1-down"
    id: relay6
    pin:
      pcf8574: pcf8574_hub_out_1
      number: 5
      mode: OUTPUT
      inverted: true
     

  - platform: gpio
    name: "curtain2-up"
    id: relay7
    pin:
      pcf8574: pcf8574_hub_out_1
      number: 6
      mode: OUTPUT
      inverted: true

     
  - platform: gpio
    name: "curtain2-down"
    id: relay8
    pin:
      pcf8574: pcf8574_hub_out_1
      number: 7
      mode: OUTPUT
      inverted: true

     
binary_sensor:
  - platform: gpio
    name: "input1"
    on_press:
      then:
        - switch.toggle: light1
    pin:
      pcf8574: pcf8574_hub_in_1
      number: 0
      mode: INPUT
      inverted: true

  - platform: gpio
    name: "input2"
    on_press:
      then:
        - switch.toggle: light2
    pin:
      pcf8574: pcf8574_hub_in_1
      number: 1
      mode: INPUT
      inverted: true

  - platform: gpio
    name: "input3"
    on_press:
      then:
        - switch.toggle: light3
    pin:
      pcf8574: pcf8574_hub_in_1
      number: 2
      mode: INPUT
      inverted: true

  - platform: gpio
    name: "input4"
    on_press:
      then:
        - switch.toggle: light4
    pin:
      pcf8574: pcf8574_hub_in_1
      number: 3
      mode: INPUT
      inverted: true

  - platform: gpio
    name: "input5"
    on_press:
      then:
        - switch.toggle: relay5
    pin:
      pcf8574: pcf8574_hub_in_1
      number: 4
      mode: INPUT
      inverted: true

  - platform: gpio
    name: "input6"
    on_press:
      then:
        - switch.toggle: relay6
    pin:
      pcf8574: pcf8574_hub_in_1
      number: 5
      mode: INPUT
      inverted: true

  - platform: gpio
    name: "input7"
    on_press:
      then:
        - switch.toggle: relay7
    pin:
      pcf8574: pcf8574_hub_in_1
      number: 6
      mode: INPUT
      inverted: true

  - platform: gpio
    name: "input8"
    on_press:
      then:
        - switch.toggle: relay8
    pin:
      pcf8574: pcf8574_hub_in_1
      number: 7
      mode: INPUT
      inverted: true

  - platform: remote_receiver
    name: "remoter1"
    rc_switch_raw:
      code: '000101000101010100000011'
      protocol: 2
    on_press:
      then:
        - switch.toggle: light1
    filters:
      - delayed_off: 200ms

  - platform: remote_receiver
    name: "remoter2"
    rc_switch_raw:
      code: '000101000101010100001100'
      protocol: 2
    on_press:
      then:
        - switch.toggle: light2
    filters:
      - delayed_off: 200ms
     
  - platform: remote_receiver
    name: "remoter3"
    rc_switch_raw:
      code: '001111010111001010110100'
      protocol: 2
    on_press:
      then:
        - switch.toggle: light3
    filters:
      - delayed_off: 200ms
     
  - platform: remote_receiver
    name: "remoter4"
    rc_switch_raw:
      code: '001111010111001010111001'
      protocol: 2
    on_press:
      then:
        - switch.toggle: light4
    filters:
      - delayed_off: 200ms 
   
  - platform: remote_receiver
    name: "remoter5"
    rc_switch_raw:
      code: '001111010111001010110010'
      protocol: 2
    on_press:
      then:
        - switch.toggle: relay5
    filters:
      - delayed_off: 200ms

  - platform: remote_receiver
    name: "remoter6"
    rc_switch_raw:
      code: '001111010111001010110101'
      protocol: 2
    on_press:
      then:
        - switch.toggle: relay6
    filters:
      - delayed_off: 200ms
     
  - platform: remote_receiver
    name: "remoter7"
    rc_switch_raw:
      code: '001111010111001010110001'
      protocol: 2
    on_press:
      then:
        - switch.toggle: relay7
    filters:
      - delayed_off: 200ms
     
  - platform: remote_receiver
    name: "remoter8"
    rc_switch_raw:
      code: '001111010111001010110011'
      protocol: 2
    on_press:
      then:
        - switch.toggle: relay8
    filters:
      - delayed_off: 200ms
     

# Enable logging
logger:

# Enable Home Assistant API
api:


.txt   KC868-A8M-ha-config.txt (Size: 5.68 KB / Downloads: 276)
YouTube: https://www.youtube.com/c/KinCony
Online Store: https://kincony.aliexpress.com
Find
Reply
multimax Offline
Junior Member
**
Posts: 6
Threads: 0
Joined: May 2023
Reputation: 0
#2
09-15-2023, 06:30 AM
Hello

i use your esp home example, but i get this error - see pic
it is like the adress for pcf8574 is wrong - i have two kc868-a8m it says the same error


Attached Files Image(s)
   
Find
Reply
admin Offline
Administrator
*******
Posts: 6,324
Threads: 808
Joined: Oct 2020
Reputation: 155
#3
09-15-2023, 06:35 AM (This post was last modified: 09-15-2023, 06:35 AM by admin.)
take a photo how you connect wire with your A8M board.
YouTube: https://www.youtube.com/c/KinCony
Online Store: https://kincony.aliexpress.com
Find
Reply
multimax Offline
Junior Member
**
Posts: 6
Threads: 0
Joined: May 2023
Reputation: 0
#4
09-15-2023, 08:05 AM
(09-15-2023, 06:35 AM)admin Wrote: take a photo how you connect wire with your A8M board.

Hello

the board is only connectet with the usb cable, and an network cable. nothing else. i just upload your code. i tryed to change the code, to see if i get an new result. but no

se txt file


Attached Files
.txt   esphome.txt (Size: 6.53 KB / Downloads: 163)
Find
Reply
admin Offline
Administrator
*******
Posts: 6,324
Threads: 808
Joined: Oct 2020
Reputation: 155
#5
09-15-2023, 08:11 AM
you have not connect with dc12v power supply??
YouTube: https://www.youtube.com/c/KinCony
Online Store: https://kincony.aliexpress.com
Find
Reply
multimax Offline
Junior Member
**
Posts: 6
Threads: 0
Joined: May 2023
Reputation: 0
#6
09-15-2023, 09:03 AM (This post was last modified: 09-15-2023, 09:10 AM by multimax.)
(09-15-2023, 08:11 AM)admin Wrote: you have not connect with dc12v power supply??

Sorry - yes power is on :-)
here is pic


Attached Files Image(s)
   
Find
Reply
admin Offline
Administrator
*******
Posts: 6,324
Threads: 808
Joined: Oct 2020
Reputation: 155
#7
09-15-2023, 10:28 AM
your esphome LOG showed, have not detected i2c bus device. i suggest you download KCS v2 firmware to test control relay whether work well firstly.
here is details: https://www.kincony.com/esp32-kcsv2-firmware.html
if KCS firmware work well, then go to next step for check ESPHOME config.
YouTube: https://www.youtube.com/c/KinCony
Online Store: https://kincony.aliexpress.com
Find
Reply
multimax Offline
Junior Member
**
Posts: 6
Threads: 0
Joined: May 2023
Reputation: 0
#8
09-20-2023, 12:19 PM
Hello

sorry for the late reply, i deleted the code, and wrote it again - and so it works :-)

about the rf part, if i read an rf433 key, i get differnt codes everytime....
if i recive it in pronto format, i get the same code everytime :-)
so do you have and pice of esp home code, where i can use pronto code to trigger an light in esp, insted off raw code ?
Find
Reply
admin Offline
Administrator
*******
Posts: 6,324
Threads: 808
Joined: Oct 2020
Reputation: 155
#9
09-20-2023, 01:04 PM
what remote you have used?
suggest use "RC-switch" signal type for decode.
YouTube: https://www.youtube.com/c/KinCony
Online Store: https://kincony.aliexpress.com
Find
Reply
multimax Offline
Junior Member
**
Posts: 6
Threads: 0
Joined: May 2023
Reputation: 0
#10
09-21-2023, 05:31 AM (This post was last modified: 09-21-2023, 05:52 AM by multimax.)
Hello itis an remote for my garage.
if i use rc_switch i get this
[07:30:57][D][remote.rc_switch:261]: Received RCSwitch Raw: protocol=1 data='0110110000100011101001101010001011010010101010111111111111111011'
[07:30:58][D][remote.rc_switch:261]: Received RCSwitch Raw: protocol=1 data='1110100100101100011000001000000011010010101010111111111111111'
[07:31:00][D][remote.rc_switch:261]: Received RCSwitch Raw: protocol=1 data='0111011101110001000110110111110111010010101010111111111111111011'
[07:31:01][D][remote.rc_switch:261]: Received RCSwitch Raw: protocol=1 data='01100111000001110010011110100001110100101'
[07:31:02][D][remote.rc_switch:261]: Received RCSwitch Raw: protocol=1 data='110000101001100111110101010011101101001010'
[07:31:03][D][remote.rc_switch:261]: Received RCSwitch Raw: protocol=1 data='0101100111001100010000100101010011010010101010111111111111111011'
[07:31:04][D][remote.rc_switch:261]: Received RCSwitch Raw: protocol=1 data='1011111101110001111100111011011111010010101010111111111111111011'
[07:31:05][D][remote.rc_switch:261]: Received RCSwitch Raw: protocol=1 data='1101001000010000011110111011001111010010101010111111111111111011'
[07:31:05][D][remote.rc_switch:261]: Received RCSwitch Raw: protocol=1 data='1100010110001010000000011110110111010010101010111111111111111011'
[07:31:06][D][remote.rc_switch:261]: Received RCSwitch Raw: protocol=1 data='0110010010000011010010011100010011010010101010111111111111111011'
[07:31:06][D][remote.rc_switch:261]: Received RCSwitch Raw: protocol=1 data='01100100100'
[07:31:07][D][remote.rc_switch:261]: Received RCSwitch Raw: protocol=1 data='0010101110000011100001111110000111010010101010111111111111111011'
[07:31:08][D][remote.rc_switch:261]: Received RCSwitch Raw: protocol=1 data='0010110010010101101111100000001011010010101010111111111111111011'
[07:31:09][D][remote.rc_switch:261]: Received RCSwitch Raw: protocol=1 data='100010000011011001000'
[07:31:10][D][remote.rc_switch:261]: Received RCSwitch Raw: protocol=1 data='11110011011000011110011101000000110100101'
and it is the same button !
Find
Reply


Forum Jump:


Users browsing this thread:
1 Guest(s)