Smart Home Automation Forum › Technical Support › KC868-A series and Uair Smart Controller v
A16 flash problem

Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Threaded Mode
A16 flash problem
admin Offline
Administrator
*******
Posts: 6,339
Threads: 811
Joined: Oct 2020
Reputation: 156
#11
11-20-2023, 10:46 AM
? take a screen photo of your error
YouTube: https://www.youtube.com/c/KinCony
Online Store: https://kincony.aliexpress.com
Find
Reply
zeltini1401 Offline
Junior Member
**
Posts: 15
Threads: 1
Joined: Nov 2023
Reputation: 0
#12
11-20-2023, 03:54 PM
(11-20-2023, 10:46 AM)admin Wrote: ? take a screen photo of your error


Attached Files Image(s)
       
Find
Reply
admin Offline
Administrator
*******
Posts: 6,339
Threads: 811
Joined: Oct 2020
Reputation: 156
#13
11-20-2023, 10:30 PM
do you have installed USB driver: https://www.kincony.com/download/CH341SER.zip
YouTube: https://www.youtube.com/c/KinCony
Online Store: https://kincony.aliexpress.com
Find
Reply
zeltini1401 Offline
Junior Member
**
Posts: 15
Threads: 1
Joined: Nov 2023
Reputation: 0
#14
11-21-2023, 06:01 AM
(11-20-2023, 10:30 PM)admin Wrote: do you have installed USB driver: https://www.kincony.com/download/CH341SER.zip


Attached Files Image(s)
   
Find
Reply
admin Offline
Administrator
*******
Posts: 6,339
Threads: 811
Joined: Oct 2020
Reputation: 156
#15
11-21-2023, 10:18 AM
change another USB cable, lower your baud rate of serial port.
make sure not use USB HUB with your computer, just use USB-C cable connect your board with PC directly.
YouTube: https://www.youtube.com/c/KinCony
Online Store: https://kincony.aliexpress.com
Find
Reply
zeltini1401 Offline
Junior Member
**
Posts: 15
Threads: 1
Joined: Nov 2023
Reputation: 0
#16
11-21-2023, 03:53 PM
(11-21-2023, 10:18 AM)admin Wrote: change another USB cable, lower your baud rate of serial port.
make sure not use USB HUB with your computer, just use USB-C cable connect your board with PC directly.

115200 speed is the lowest that can be selected. The cable is your original. Same thing with another wire. The wire is connected directly to the board, without any transitions. Is it possible to connect remotely? It will take you a few minutes to connect and adopt the settings like a pro.
Find
Reply
admin Offline
Administrator
*******
Posts: 6,339
Threads: 811
Joined: Oct 2020
Reputation: 156
#17
11-21-2023, 11:46 PM (This post was last modified: 11-21-2023, 11:46 PM by admin.)
1. Do you have connected DC12v power supply for KC868-A16?
2. if you installed RF433M module, please remove it when download firmware.
take a photo of your board, how you wire.
YouTube: https://www.youtube.com/c/KinCony
Online Store: https://kincony.aliexpress.com
Find
Reply
zeltini1401 Offline
Junior Member
**
Posts: 15
Threads: 1
Joined: Nov 2023
Reputation: 0
#18
11-22-2023, 06:09 AM (This post was last modified: 11-22-2023, 06:09 AM by zeltini1401.)
(11-21-2023, 11:46 PM)admin Wrote: 1. Do you have connected DC12v power supply for KC868-A16?
2. if you installed RF433M module, please remove it when download firmware.
take a photo of your board, how you wire.

Good morning. After removing the RF modul, the program recorded. I'll try to record skits later.


Attached Files Image(s)
   
Find
Reply
admin Offline
Administrator
*******
Posts: 6,339
Threads: 811
Joined: Oct 2020
Reputation: 156
#19
11-22-2023, 09:51 AM
it's ok now, just remove RF module when download.
YouTube: https://www.youtube.com/c/KinCony
Online Store: https://kincony.aliexpress.com
Find
Reply
zeltini1401 Offline
Junior Member
**
Posts: 15
Threads: 1
Joined: Nov 2023
Reputation: 0
#20
11-25-2023, 04:52 PM (This post was last modified: 11-25-2023, 04:54 PM by zeltini1401.)
Hello. I started from the beginning. I loaded the KCS_KC868_A16_V2.1.9.bin file according to the instructions. There is a wifi network. Lan cable shows as "Unidentified Network" and sketch "Failed....".


Attached Files Image(s)
   
Find
Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)