+- Smart Home Automation Forum (https://www.kincony.com/forum)
+-- Forum: Technical Support (https://www.kincony.com/forum/forumdisplay.php?fid=1)
+--- Forum: KC868-A series and Uair Smart Controller (https://www.kincony.com/forum/forumdisplay.php?fid=6)
+--- Thread: KC868-HA RS485 INPUT & OUTPUT plugin for ESPHome (/showthread.php?tid=3397)
RE: KC868-HA RS485 INPUT & OUTPUT plugin for ESPHome - gizmo - 12-18-2023
(12-18-2023, 12:23 AM)admin Wrote: use mulit meter test HAv2 OUTPUT1-6 when voltage will change if your turn ON/OFF on home assistant.
Measuring from the outputs to GND, it shows +3.8v and this does not change if i turn the switch on of off in Home Assistant.
RE: KC868-HA RS485 INPUT & OUTPUT plugin for ESPHome - admin - 12-18-2023
when you setup complete in PC config tool.
Do you have click the "ApplyTo" button and "SaveFlash" button? Must need press these two buttons.
RE: KC868-HA RS485 INPUT & OUTPUT plugin for ESPHome - gizmo - 12-18-2023
(12-18-2023, 10:45 PM)admin Wrote: when you setup complete in PC config tool.
Do you have click the "ApplyTo" button and "SaveFlash" button? Must need press these two buttons.
Yes, I pressed "ApplyTo" and then "SaveFlash". See the screenshot of the config i just saved again.
RE: KC868-HA RS485 INPUT & OUTPUT plugin for ESPHome - admin - 12-18-2023
can you post the newest yaml with latest KC868-HA component (v3.0.0).
RE: KC868-HA RS485 INPUT & OUTPUT plugin for ESPHome - gizmo - 12-18-2023
(12-18-2023, 11:09 PM)admin Wrote: can you post the newest yaml with latest KC868-HA component (v3.0.0).
esphome:
name: dingtian-4ch
friendly_name: dingtian-4ch
esp32:
board: esp32dev
framework:
type: arduino
# Enable logging
logger:
baud_rate: 0
# Enable Home Assistant API
api:
encryption:
key: "XXX"
ota:
password: "XXX"
status_led:
pin:
number: GPIO15
inverted: true
uart:
id: myuart1
tx_pin: GPIO1
rx_pin: GPIO3
baud_rate: 9600
ethernet:
type: JL1101
mdc_pin: GPIO23
mdio_pin: GPIO18
phy_addr: 0
clk_mode: GPIO17_OUT
# The PHY chip has a pin labeled TX_EN that goes to GPIO 21 on ESP
# and the RSTn pin on the phy goes to GPIO0
##
# Datasheet indicates the RSTn should be LOW to disable the phy and default is high
power_pin: GPIO0
external_components:
- source:
type: git
url: https://github.com/hzkincony/esphome-kc868-ha
ref: main
kc868_ha:
binary_sensor:
- platform: kc868_ha
target_relay_controller_addr: 1 # Default value is 1, corresponds to the Target Relay Controller Addr parameter in HA485_Ctrl software
switch_adapter_addr: 10 # Default value is 10, corresponds to the Switch Adapter Addr parameter in HA485_Ctrl software
bind_output: 1 # Corresponds to the BindOutput parameter in HA485_Ctrl software
name: "binary_sensor 1"
- platform: kc868_ha
target_relay_controller_addr: 1
switch_adapter_addr: 10
bind_output: 2
name: "binary_sensor 2"
- platform: kc868_ha
target_relay_controller_addr: 1
switch_adapter_addr: 10
bind_output: 3
name: "binary_sensor 3"
- platform: kc868_ha
target_relay_controller_addr: 1
switch_adapter_addr: 10
bind_output: 4
name: "binary_sensor 4"
- platform: kc868_ha
target_relay_controller_addr: 1
switch_adapter_addr: 10
bind_output: 5
name: "binary_sensor 5"
- platform: kc868_ha
target_relay_controller_addr: 1
switch_adapter_addr: 10
bind_output: 6
name: "binary_sensor 6"
switch:
- platform: kc868_ha
target_relay_controller_addr: 1
switch_adapter_addr: 10
bind_output: 1
name: "switch 1"
- platform: kc868_ha
target_relay_controller_addr: 1
switch_adapter_addr: 10
bind_output: 2
name: "switch 2"
- platform: kc868_ha
target_relay_controller_addr: 1
switch_adapter_addr: 10
bind_output: 3
name: "switch 3"
- platform: kc868_ha
target_relay_controller_addr: 1
switch_adapter_addr: 10
bind_output: 4
name: "switch 4"
- platform: kc868_ha
target_relay_controller_addr: 1
switch_adapter_addr: 10
bind_output: 5
name: "switch 5"
- platform: kc868_ha
target_relay_controller_addr: 1
switch_adapter_addr: 10
bind_output: 6
name: "switch 6"
RE: KC868-HA RS485 INPUT & OUTPUT plugin for ESPHome - admin - 12-18-2023
external_components:
- source:
type: git
url: https://github.com/hzkincony/esphome-kc868-ha
ref: v3.0.0
use "v3.0.0" , you have use "main". change it.
i don't know which esp32 board model you are using? i can't see in your photo.
maybe you can exchange RXD and TXD pin define.
Now do you INPUT port for binary sensor work well? only OUTPUT can't work?
RE: KC868-HA RS485 INPUT & OUTPUT plugin for ESPHome - gizmo - 12-18-2023
(12-18-2023, 11:31 PM)admin Wrote: external_components:
- source:
type: git
url: https://github.com/hzkincony/esphome-kc868-ha
ref: v3.0.0
use "v3.0.0" , you have use "main". change it.
i don't know which esp32 board model you are using? i can't see in your photo.
maybe you can exchange RXD and TXD pin define.
Now do you INPUT port for binary sensor work well? only OUTPUT can't work?
I started with “ref: v3.0.0” and changed it to “ref: main” so I would always have the latest version. But it doesn’t work with either option anyway.
The INPUT binary sensors work perfectly. If i press a button, it registers correctly in Home Assistant.
It’s only the OUTPUT that doesn’t work.
RE: KC868-HA RS485 INPUT & OUTPUT plugin for ESPHome - admin - 12-19-2023
ok, later we check.
RE: KC868-HA RS485 INPUT & OUTPUT plugin for ESPHome - gizmo - 12-19-2023
(12-19-2023, 02:41 AM)admin Wrote: ok, later we check.
Thank you very much, I hope to hear back soon
RE: KC868-HA RS485 INPUT & OUTPUT plugin for ESPHome - admin - 12-20-2023
after we tested, when have news, will feedback at here.