+- Smart Home Automation Forum (https://www.kincony.com/forum)
+-- Forum: Technical Support (https://www.kincony.com/forum/forumdisplay.php?fid=20)
+--- Forum: KC868-ATC / Tuya adapter V2 (https://www.kincony.com/forum/forumdisplay.php?fid=32)
+--- Thread: KC868-ATC v1.4 connect to H32 rev 2.3 (/showthread.php?tid=7408)
KC868-ATC v1.4 connect to H32 rev 2.3 - SrgX13 - 01-18-2025
Hello,
I have been trying for a few days to set up the KC868-ATC v1.4 with Tuya module to connect to KC868-H32 rev 2.3 and control the relays. I managed to set the KC868-ATC Tuya module and connect using Tuya mobile App (Android), however the button/switches are not responding.
The weird part is that I can connect to KC868-H32 using Vircom and the IP seems to be set to 192.168.2.160 (we are using 192.168.2.x ranges). From what I have seen in the referred videos is that I should also be able to connect using the browser however this is failing. KC868-H32 is connected to the router through Ethernet cable
I have even tried to set KC868-ATC v1.4 to use RS232 instead of wifi. This had the same negative results.
If you require more information please let me know.
Please help me with some ideas how to set this system. I assume that I might have to change the firmware on KC868-H32 as in Tuya it was showing H32B PRO
Thank you very much and I wish you a great day
RE: KC868-ATC v1.4 connect to H32 rev 2.3 - admin - 01-19-2025
post your H32 vircom setting screen photo at here. make sure you have set network work mode= "TCP Server", then MUST re power on of your H32.
tuya adapter use by wifi is better.
RE: KC868-ATC v1.4 connect to H32 rev 2.3 - SrgX13 - 01-19-2025
(01-19-2025, 01:19 AM)admin Wrote: post your H32 vircom setting screen photo at here. make sure you have set network work mode= "TCP Server", then MUST re power on of your H32.
tuya adapter use by wifi is better.
Hello and thank you for your reply
Attached is the image with Vircom connected to H32. I did set the mode to TCP Server and restarted H32. For the KC868-ATC I tried wifi with no success. I attached additional screens with H32, KC868-ATC and the flashing process.
The H32 is connected to the main router. There is a secondary router configured as AP for the main router. Should the KC868-ATC be flashed/configured to the main router? When i tried it was connected to the secondary one (AP for the main).
Any suggestions are more then welcome.
Thank you very much
RE: KC868-ATC v1.4 connect to H32 rev 2.3 - admin - 01-19-2025
tuya adapter and H32 should connect to same router, just one local network.
RE: KC868-ATC v1.4 connect to H32 rev 2.3 - SrgX13 - 01-20-2025
(01-19-2025, 11:58 PM)admin Wrote: tuya adapter and H32 should connect to same router, just one local network.
Hello. Thank you very much. Although the secondary router was set up as an AP for the primary router (where H32 was connected) and I could ping it and check it in Vircom from the secondary router, I had to connect both H32 and KC868-ATC to the same router (primary router).
I wish you a great day
RE: KC868-ATC v1.4 connect to H32 rev 2.3 - admin - 01-20-2025
ok, work well now?