[KC868-AG PRO] Tuya and scenes

[zolax]

Hello,
I need to control 40 Tuya window actuators with one RF433MHz remote control.
For this I need to read 40 x 2 signals (window opening and closing) RF433MHz from my 99CH RF remote and create scenes in TUYA. The Kincony device is intended to act as an intermediary between the 99CH RF433MHz remote control (not Tuya) and the actuators (Tuya).
Previously, I bought KC-868-A4, but it only supports 32 RF signals and 4 outputs (I only need virtual ones for tuya), which practically allows for the control of only 4 actuators.

I bought KC868-AG PRO and the problem is that:
- in KC868-A4 PRO for e.g. output 1 there was a signal: output1:off, output 1:on and it worked very well
- in KC868-AG PRO I create e.g. Window Pusher, configured the RF signal but I have no on/off condition, only e.g. Scene1: scene and it doesn't work

[admin]

KC868-AG Pro support use Tuya app to learn your RF remoter button directly. you can learn your window RF433Mhz signal directly.

[zolax]

KC868-AG Pro support use Tuya app to learn your RF remoter button directly. you can learn your window RF433Mhz signal directly.

Yes and this function works but after learned I can not use this signal in scene. There is no on/off signal, just "Scene 1: scene" not output1:off /on.

[KinCony Support]

KC868-AG Pro support use Tuya app to learn your RF remoter button directly. you can learn your window RF433Mhz signal directly.

Yes and this function works but after learned I can not use this signal in scene. There is no on/off signal, just "Scene 1: scene" not output1:off /on.

We tested AG-PRO's 433 signal learning and triggering. 433 signals can be learned normally, It can send 433 signals through scene mode
   

[zolax]

KC868-AG Pro support use Tuya app to learn your RF remoter button directly. you can learn your window RF433Mhz signal directly.

Yes and this function works but after learned I can not use this signal in scene. There is no on/off signal, just "Scene 1: scene" not output1:off /on.

We tested AG-PRO's 433 signal learning and triggering. 433 signals can be learned normally, It can send 433 signals through scene mode

Thanks but this doesn't work for what I need.
My 99CH RF433MHz remote is not from set with the actuators (its radio signal doesn't work directly with actuators). 
I don't need to 
learn 433MHz remote signal and send 433MHz signal from the app instead, 
but 
learn 433MHz remote signal and send tuya action to tuya actuator. My actuators don't have radio reciver, I can control them only by Tuya.
I hope I described it clear enough, if not pelase let me know.

[admin]

- in KC868-AG PRO I create e.g. Window Pusher, configured the RF signal but I have no on/off condition, only e.g. Scene1: scene and it doesn't work
about this question, can you take a phone screen photo, where can't see what?

[zolax]

- in KC868-AG PRO I create e.g. Window Pusher, configured the RF signal but I have no on/off condition, only e.g. Scene1: scene and it doesn't work
about this question, can you take a phone screen photo, where can't see what?

I attached screen from A4 and AG.

[admin]

if you want received 433M signal THEN turn ON relay. IF "condition" chose KC868-AG Pro --> 433M learned signal.

[zolax]

if you want received 433M signal THEN turn ON relay. IF "condition" chose KC868-AG Pro --> 433M learned signal.

There is no possible to choose KC868-AG-Pro condition. There is only stuff "generated" by it like Window Pusher etc. 
Maybe you could make a screen with KC868-AG-Pro selected as a condition. I have newest Tuya version on the phone.
This was possible with A4 but not with AG.

[KinCony Support]

if you want received 433M signal THEN turn ON relay. IF "condition" chose KC868-AG Pro --> 433M learned signal.

There is no possible to choose KC868-AG-Pro condition. There is only stuff "generated" by it like Window Pusher etc. 
Maybe you could make a screen with KC868-AG-Pro selected as a condition. I have newest Tuya version on the phone.
This was possible with A4 but not with AG.

According to your question, I think you can use 3 pieces of KC868-A4, then the wireless signal will be programmed 32*3=96, we ask the tuya support ,it is not support  received RF signal to be an if command, tuya app cannot implement the IF command like KC868-A4.