Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
KC868-AP
#24
(05-07-2023, 09:04 AM)OloffSmyth Wrote: I would like to connect a Nextion HMI to a KC868 AIO All in One Controller. 
Please advise on best pins to use.

if you not use 4G module, you can use 4G socket's RXD,TXD pin for Nextion display.
Reply


Messages In This Thread
KC868-AP - by eligijus - 03-05-2023, 07:23 PM
RE: KC868-AP - by admin - 03-06-2023, 12:07 AM
RE: KC868-AP - by eligijus - 03-06-2023, 04:12 PM
RE: KC868-AP - by admin - 03-06-2023, 10:44 PM
RE: KC868-AP - by eligijus - 04-17-2023, 03:27 PM
RE: KC868-AP - by admin - 04-18-2023, 06:29 AM
RE: KC868-AP - by eligijus - 04-18-2023, 01:19 PM
RE: KC868-AP - by admin - 04-18-2023, 10:51 PM
RE: KC868-AP - by eligijus - 04-24-2023, 03:58 PM
RE: KC868-AP - by admin - 04-25-2023, 12:40 AM
RE: KC868-AP - by eligijus - 04-27-2023, 06:10 AM
RE: KC868-AP - by admin - 04-27-2023, 08:32 AM
RE: KC868-AP - by eligijus - 04-28-2023, 06:19 AM
RE: KC868-AP - by admin - 04-29-2023, 02:41 AM
RE: KC868-AP - by eligijus - 04-30-2023, 03:33 PM
RE: KC868-AP - by admin - 05-01-2023, 12:36 AM
RE: KC868-AP - by eligijus - 05-01-2023, 08:17 PM
RE: KC868-AP - by admin - 05-01-2023, 11:44 PM
RE: KC868-AP - by eligijus - 05-06-2023, 06:52 PM
RE: KC868-AP - by admin - 05-07-2023, 04:21 AM
RE: KC868-AP - by admin - 05-07-2023, 04:33 AM
RE: KC868-AP - by eligijus - 05-07-2023, 05:50 AM
RE: KC868-AIO - by OloffSmyth - 05-07-2023, 09:04 AM
RE: KC868-AP - by admin - 05-07-2023, 09:53 AM
RE: KC868-AP - by OloffSmyth - 06-25-2023, 09:10 AM
RE: KC868-AP - by admin - 05-08-2023, 12:49 AM
RE: KC868-AP - by eligijus - 05-08-2023, 05:53 PM
RE: KC868-AP - by admin - 05-09-2023, 12:51 AM
RE: KC868-AP - by eligijus - 05-10-2023, 10:51 AM
RE: KC868-AP - by admin - 05-10-2023, 10:58 AM
RE: KC868-AP - by eligijus - 05-10-2023, 11:11 AM
RE: KC868-AP - by admin - 05-10-2023, 12:04 PM
RE: KC868-AP - by eligijus - 05-10-2023, 12:19 PM
RE: KC868-AP - by admin - 05-10-2023, 12:24 PM
RE: KC868-AP - by admin - 06-25-2023, 11:07 AM

Forum Jump:


Users browsing this thread:
1 Guest(s)