Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
H32L issue
#1
I have a kc868-H32L controller.
I programmed it to be in a motor mood.

When i turn on relay(1 or 2 or 3…..or 32) by button switch module, relay (1 or 2 or 3…..or 32)will be on for 1 minute, and after that will turn off automatically.

If (for example) i turn on relay1, then i turn on relay2, so relay1 will be OFF (because control is in motor mood)

Now, if i do all the above by kincony smart home app, I don’t get same results. Which means: 

➡️ if i turn on relay1, then relay1 will be on forever, and don’t turn off after 1 minute automatically.
And if i turn on relay1, and then turn on relay2, the relay1 will not turn off and it stays turned on.

Why is that❓
Is there any solution ❓
Reply
#2
take a photo of your controller , i want to see how you wire. do you use switch terminal board? if you are using switch terminal board, you can set for "MOTOR" mode.
Reply
#3
Yes, i do use switch terminal board. And i set the controller for motor mood. That’s not the problem.

The problem is when i use the kincony smart home app, as I described in the post above ⬆️⬆️⬆️⬆️⬆️⬆️⬆️

(04-11-2024, 04:55 AM)Saif Kitany Wrote: Yes, i do use switch terminal board. And i set the controller for motor mood. That’s not the problem.

The problem is when i use the kincony smart home app, as I described in the post above ⬆️⬆️⬆️⬆️⬆️⬆️⬆️


Attached Files Image(s)
   
Reply
#4
i suggest you add one Tuya adapter, so that can use tuya app, create scene mode to use. such as create scene mode: relay1 ON, relay2 OFF.
added tuya adapter, will support voice control by alexa and google home.
tuya adapter details: https://www.kincony.com/esp32-tuya-iot-adapter.html
Reply
#5
I added tuya adapter, and I created a scene (if relay1-ON then relay2-OFF)&(If relay2-ON then relay1-OFF).

But I noticed that there is a small problem:

For example, when i turn on relay1, and I turn on relay2, then relay1 turn OFF after less than a second!! But in this small period of time, the motor will get electricity for both directions UP&DOWN, and it’s not good for the motor!!

Is there any solution to minimize this time for relay1 changing status?
Reply
#6
when you create scene mode in tuya app, add "DELAY" time action.
Reply
#7
Got it.

Can I use one Tuya adapter for 2 controllers H32B and H32L in the same time connecting them by rs232 spliter?
Reply
#8
no, one relay controller need one tuya adapter.
if you have 2 relay controllers, you need add 2 tuya adapters.
Reply
#9
Another question:

My H32L is in motor mood,

Why when i turn on for example relay1, by switch terminal board, then the relay will be OFF after 1 minute, but if i turn it on by kincony smart home app or by tuya app, it will be ON all the time, till i turn it OFF(not after 1 minutes)?

Now, i know that i can put a timer by tuya app, but i want to understand :

1. Why the relay turned OFF after 1 minute just by switch terminal board?

2. If the H32L controller set in motor mode, shouldn’t the relays turn OFF after 1 minutes no matter the commands source? Which means (switch terminal board, kincony smart home app, tuya app, Kbox app, etc…)??!!
Reply
#10
because the switch terminal board work as MOTOR mode for shutter or curtain. if people forget to STOP motor, it will auto off after 1 minutes to protect motor.
i suggest you replace switch terminal board with KC868-AK board, so that can set every buttons logical by yourself.
Reply


Forum Jump:


Users browsing this thread:
1 Guest(s)