KC868-A16 "input1 toggle output1" automation rules in Tasmota

[admin]

this rules sample will set KC868-A16 input1 toggle output1.

for example if input1 -- toggle --> output1:

rule1 on PCF8574-1_INP#D0=0 do power1 toggle endon
rule1 1

if input2 -- toggle --> output2:

rule2 on PCF8574-1_INP#D1=0 do power2 toggle endon
rule2 1

if input3 -- toggle --> output3:

rule3 on PCF8574-1_INP#D2=0 do power3 toggle endon
rule3 1

here are setting photos for sample rule1:

   
   
   
   

[pmotshegwa]

I'm getting a command error when adding additional rules e.g.

rule4 on PCF8574-1_INP#D3=0 do power4 toggle endon
rule4 1

[admin]

rule1-3 work well?

[pmotshegwa]

rule1-3 work well?

yes, rules 1,3, and 3 are ok.

[pmotshegwa]

I ended up creating just 2 rules like this:

rule1
on PCF8574-1_INP#D0=0 do power1 toggle endon
on PCF8574-1_INP#D1=0 do power2 toggle endon
on PCF8574-1_INP#D2=0 do power3 toggle endon
on PCF8574-1_INP#D3=0 do power4 toggle endon
on PCF8574-1_INP#D4=0 do power5 toggle endon
on PCF8574-1_INP#D5=0 do power6 toggle endon
on PCF8574-1_INP#D6=0 do power7 toggle endon
on PCF8574-1_INP#D7=0 do power8 toggle endon
rule1 1

rule2
on PCF8574-2_INP#D0=0 do power9 toggle endon
on PCF8574-2_INP#D1=0 do power10 toggle endon
on PCF8574-2_INP#D2=0 do power11 toggle endon
on PCF8574-2_INP#D3=0 do power12 toggle endon
on PCF8574-2_INP#D4=0 do power13 toggle endon
on PCF8574-2_INP#D5=0 do power14 toggle endon
on PCF8574-2_INP#D6=0 do power15 toggle endon
on PCF8574-2_INP#D7=0 do power16 toggle endon
rule2 1

It's ok now

[admin]

Rule1
on PCF8574-1_INP#D0=0 do power1 toggle endon
on PCF8574-1_INP#D1=0 do power2 toggle endon
on PCF8574-1_INP#D2=0 do power3 toggle endon
on PCF8574-1_INP#D3=0 do power4 toggle endon
on PCF8574-1_INP#D4=0 do power5 toggle endon
on PCF8574-1_INP#D5=0 do power6 toggle endon
on PCF8574-1_INP#D6=0 do power7 toggle endon
on PCF8574-1_INP#D7=0 do power8 toggle endon
on PCF8574-2_INP#D0=0 do power9 toggle endon
on PCF8574-2_INP#D1=0 do power10 toggle endon
on PCF8574-2_INP#D2=0 do power11 toggle endon
on PCF8574-2_INP#D3=0 do power12 toggle endon
on PCF8574-2_INP#D4=0 do power13 toggle endon
on PCF8574-2_INP#D5=0 do power14 toggle endon
on PCF8574-2_INP#D6=0 do power15 toggle endon
on PCF8574-2_INP#D7=0 do power16 toggle endon

use one rule1 will be ok.

[admin]

   

[Isaac639]

Is there a way to send a command over IP when an input is clicked?
Thankyou.

[admin]

i have not tried this by tasmota, but if you can write arduino code, this function will be very easy to do.